Trinity 620005 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 42

Trinity 620005 Скачать руководство пользователя страница 4

TrinityHighway.com

3

Revision F November 2021

Customer Service Contacts

Trinity Highway is committed to the highest level of customer service. Feedback regarding CASS

®

S3, its assembly procedures, supporting documentation, and performance is always welcome.
Additional information can be obtained from the contact information below:

Trinity Highway

Telephone

(888) 356-2363 (USA)
+1 214 589 8140 (International)

Contact Link

TrinityHighway.com\Contact

Website:

www.trinityhighway.com

Trinity Highway Products, LLC

15601 Dallas Parkway

Suite 525

Addison, TX 75001

Important Introductory Notes

Proper assembly of CASS

®

S3 is essential to achieve the performance that has been evaluated and

deemed eligible for federal-aid reimbursement by the FHWA per NCHRP Report 350 and to AASHTO
MASH. These instructions are to be read in their entirety and understood before assembling CASS

®

S3.

These instructions are to be used only in conjunction with standard CASS

®

S3 assemblies specified by the

state/specifying agency.

If you need additional information, or have questions about CASS

®

S3,

please contact the state/specifying agency that has planned and specified this assembly and, if
needed, contact Trinity Highway Customer Service.

This product must be assembled in the location

specified by the state/specifying agency. If there are deviations, alterations, or departures from the
assembly instructions specified in this manual, the device may not perform as tested.

Note: The Metric conversion from Imperial in this manual uses a soft conversion.

A state/specifying agency’s careful evaluation of the site layout, vehicle population type and speed, traffic
direction, and visibility are some of the elements that require evaluation in the selection of a highway
product. For example, curbs could cause an untested effect on an impacting vehicle.

A set of product and project shop drawings will be supplied by Trinity Highway. The shop drawings will be
for each section of the assembly. These drawings are to be reviewed and studied thoroughly by a qualified
individual who is skilled in interpreting them.

«
...
2
3
4
5
6
...
»

Содержание 620005











































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды