background image

SecureMesh

TM

 Gateway 

 

Installation Guide 

Trilliant Incorporated 

page 22 of 23 

Making Robust and Lasting Connections 

Regardless of the grounding point you use, make sure the connections are capable of retaining low resistance 
and integrity over time and with exposure to the elements by use of an antioxidant compound.  For protection 
against corrosion and rust, wrap all connections with a product such as Scotch

®

 130C or 2228 Rubber Mastic 

Tape.   

Grounding Checklist 

When grounding a SecureMesh WAN device, use the following checklist to confirm that your installation is 
adequately protected from power surges and lightning. 

  Install all lightning and surge protection devices in accordance with UL 96A installation requirements for 

lightning protection systems and the NFPA 780 standard for lightning protection.   

  Connect a ground wire from the SecureMesh WAN device to a ground system on the utility pole, tower, 

or building. 

  When using outdoor Ethernet cable, use UV protected, 

Shielded Twisted Pair (STP) CAT5e cabling that includes a 
drain wire.  The drain wire and cable shield should be 
connected to the appropriate ground location on the 
SecureMesh WAN device; typically the ground lug inside the 
surge protector or the ground point on the outside of the device.  
Leave the other end of the drain wire at the power source 
unconnected. 

  Use the proper size down lead to connect the SecureMesh 

WAN device on a roof or tower to the ground system. 

  Whenever possible, verify that all points of the ground system 

are tied together with less than 5 ohms resistance between any 
two points. 

For Towers and Rooftops

 

  Use the proper size down lead to connect the SecureMesh WAN device on a roof or tower to the 

ground system. 

  Run the CAT5e cable inside the tower structure, tying the cable to the tower leg at every 4 feet of 

length.  For increased protection, run the CAT5e cable through metallic conduit installed on the tower. 

 

 

 

 

 

 

cable jacket 

twisted pairs 

drain wire 

Shielded Twisted Pair (STP) Ethernet cable 

with grounding drain wire 

cable shield 

Содержание SecureMesh GATE-1000
























Отзывы: