Trident FOAMATE 2.1 Скачать руководство пользователя страница 2

Trident Emergency Products, LLC
2940 Turnpike Drive | Suite #9 | Hatboro, PA 19040 USA

2

FOAMATE

™ 2.1 ATP Foam System

FOAMATE

Foamate 2.1 General Information

Trident’s FOAMATE™ 2.1 ATP is an around-the-pump foam proportioning system that adds fast and easy to operate 

Class B

 

foam capabilities to any fire apparatus. The system utilizes a brass eductor installed on the discharge side of the fire pump 
to send a small volume of water back to the suction side of the fire pump. The venturi action of the eductor creates a vacuum 
at the foam concentrate inlet allowing foam to be pulled through the metering valve, into the water stream. The foam solution 
is discharged back to the suction side of the fire pump and sent through all the discharge piping – allowing foam solution to 
be available for each discharge outlet. The brass metering valve allows for injection rates of 1%, 3% and 6% at variable flow 
rates and pressures. Units are available in either GPM or LPM flow designations and are configured with either Victaulic™ or 
FNPT connections. 

NOTE

: Throughout this document, Victaulic ends are referred to as VIC.

Contents

Maximum System Flow Rates: ��������������������������������������������������������������������������������������������������������������������������������������������2
Foamate 2�1 General Information ����������������������������������������������������������������������������������������������������������������������������������������2
Performance and Operating Parameters ����������������������������������������������������������������������������������������������������������������������������2
Installation Instructions �������������������������������������������������������������������������������������������������������������������������������������������������������3
Foam System Operating Procedures from On-Board Foam Tank ��������������������������������������������������������������������������������������4
Foam System Operating Procedures from External Auxiliary Foam Concentrate Source ��������������������������������������������������4
General Operating Tips for ATP Foam Systems ������������������������������������������������������������������������������������������������������������������4
Foam System Shutdown Instructions ���������������������������������������������������������������������������������������������������������������������������������4
Foam System Flushing Instructions ������������������������������������������������������������������������������������������������������������������������������������4
Schematic/Instruction Plate Template ���������������������������������������������������������������������������������������������������������������������������������5
Metering Valve/Dial Template ����������������������������������������������������������������������������������������������������������������������������������������������5
Piping Schematic ����������������������������������������������������������������������������������������������������������������������������������������������������������������6
Benefits of an External Pickup Tube - Enhancing Your Foam System ��������������������������������������������������������������������������������7
Model Numbers and Parts Listing ���������������������������������������������������������������������������������������������������������������������������������������8
Metering Valve Details ���������������������������������������������������������������������������������������������������������������������������������������������������������9
Foam System Maintenance �����������������������������������������������������������������������������������������������������������������������������������������������10
Foamate 2�1 Rebuild Kit ����������������������������������������������������������������������������������������������������������������������������������������������������10
Installation Notes ���������������������������������������������������������������������������������������������������������������������������������������������������������������11
Operating Notes ����������������������������������������������������������������������������������������������������������������������������������������������������������������11
Other Foam System Products �������������������������������������������������������������������������������������������������������������������������������������������12

Maximum System Flow Rates:

1% Injection: 2000 GPM 

[8000 LPM]

3% Injection: 2000 GPM 

[8000 LPM]

6% Injection: 1000 GPM 

[4000 LPM]

Performance and Operating Parameters

 

„

Eductor

: All brass construction. 1

1

2

[38 mm]

 water inlet, 2" 

[50 mm]

 foam concentrate inlet, 2" 

[50 mm] 

foam solution 

outlet. All connections are pipe groove Victaulic.

 

„

Eductor Flow

: 85 GPM 

[320 LPM]

 at 125 PSI 

[8.5 Bar].

 

„

System Operating Pressure

: 125 – 250 PSI 

[8.5 – 17 Bar].

 

„

Flow Rates

: Variable flow rates to multiple discharge outlets 

up to the maximum foam system capacity.

 

„

Factory calibrated. Meets NFPA Standards.

 

„

Metering Valve

: All brass construction. 2" 

[50 mm] 

pipe 

groove Victaulic or FNPT foam concentrate inlet and outlet.

 

„

All discharge outlets provide foam solution at the same time.

 

„

No back pressure restriction from hose lengths or elevation.

 

„

Compatible with any type of foam concentrate and foam 
making nozzle.

 

„

Fire pump operations do not change.

 

„

Maximum fire pump inlet pressure: 5 PSI 

[0.35 Bar].

Содержание FOAMATE 2.1













Отзывы: