manualshive.com logo in svg

TriangleTube Delta, Руководство по установке и обслуживанию

Поделиться
Скачать
TriangleTube Delta Скачать руководство пользователя страница 39

33

Start-Up Preparation

System water, including additives must be

practically non-toxic, having a toxicity

rating of Class 1, as listed in Clinical

Toxicology of Commercial Products.

Use of Antifreeze in the Primary System

NEVER use automotive or ethylene gly-

col antifreeze or undiluted antifreeze in

the primary system as freeze protection.

This can cause severe personal injury,

death or substantial property damage if

ignored.

Determine the antifreeze fluid quantity
using the system water content volume and
following the antifreeze manufacturer
instructions.

The primary outer tank volume of the
MODULATING DELTA is approximately
20 gallons.  Remember to include the vol-
ume of the expansion tank.

Check with local codes requirements for
the installation of back flow preventers or
actual disconnect from the make up water
supply line.

Ensure the concentration of antifreeze to
water does not exceed a 50/50 ratio.

System water including additives must be

practically non-toxic, having a toxicity

rating of Class 1, as listed in Clinical

Toxicology of Commercial Products.

Filling the Inner (Domestic) Tank and

System

Proceed with filling instructions for the

inner and outer tanks only after ensur-

ing the water meets the requirements

listed in this installation manual.  Failure

to comply could result in damage and

improper operation of the appliance.

Never operate the MODULATING

DELTA unless both the inner and outer

tanks are completely filled.

Always fill the inner tank prior to filling

and pressurizing the outer tank.  Failure

to properly fill the inner tank could

result in damage to the inner tank.

1.  Ensure the domestic drain valve is closed.

2.  Open the isolation valves on the domestic

cold supply piping to the MODULATING
DELTA and on the domestic hot outlet pip-
ing to the building (if provided).

3.  Vent any air from the domestic piping sys-

tem by opening faucets near the appliance.
Continue filling the domestic system until
there is a constant flow of water from the
faucets.

4.  Close the hot water faucets.

Filling the Outer (Primary) Tank and

System

1.  Close the primary drain valve located on

the rear of the appliance and any manual or
automatic air vent in the system.

2.  Open all system isolation valves.

CAUTION

CAUTION

WARNING

NOTICE

WARNING

NOTICE

Содержание Delta

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды