Tri-Star TAC-10X Скачать руководство пользователя страница 33

Страница: 33 / 39

Page 33

Step 5.

Using only hand pressure, extend the arbor as far to the left as it will

go.

Step 6.

Using appropriate GO NO-GO gauges, open the funnel and insert

gauges into the indenters to determine the "G" dimensions.

to correspond to the largest wire size.

NOTE: Be sure to use gauges corresponding to proper wire gauge and contact

gauge.

Step 7.

If the "G" dimension is acceptable, go to Step 14. If the "G" dimension

is not acceptable, go to Step 8.

Step 8.

Refer to Figure 6-6.

Step 9.

Loosen the Stafford clamp collar.

Step 10.

Rotate the "ADJUST' adjustable stop counter clockwise to decrease

the "G" dimension, or clockwise to increase the "G" dimension.

Step 11.

Repeat Steps 5 through 10 until the "G" dimension is within acceptable

parameters.

Step 12.

Hand-tighten the Stafford clamp collar, being careful not to change the

adjustable stop position.

Step 13.

Repeat steps 5 and 6.

NOTE: Operator-adjustable "G" dimension TAC's should be adjusted at setting 6. If

desired after adjustment has been completed, GO NO-GO verification may be

performed for the remaining settings.

Step 14.

Install the crimp cylinder arbor cover plate and the funnel cover plate

removed in Step 3.

Step 15.

Connect the air supply to the sleeve valve.

Step 16.

Set the feeder-bowl power on-off switch to on.

Step 17.

Close the sleeve valve.

Step 18.

Verify a contact is seated in the transfer tip and that the transfer tip is in

the ready-to-crimp position.

Step 19.

Using a conductor of proper material and gauge, strip it to the proper

strip length. Be sure the "G" dimension, if applicable, is at the proper

setting.

Step 20.

While being careful that all conductor strands enter the funnel without

bending back, insert the conductor into the funnel until it bottoms out.

Содержание TAC-10X








































Результаты поиска

Содержание TAC-10X

Отзывы:

Похожие инструкции для TAC-10X

Бренды по названию

Популярные бренды

Tri-Star TAC-10X, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание TAC-10X

Отзывы:

Похожие инструкции для TAC-10X

Бренды по названию

Популярные бренды