manualshive.com logo in svg

TRENDnet TV-IP430PI, Руководство пользователя, Страница: 6 / 58

Поделиться
Скачать
TRENDnet TV-IP430PI Скачать руководство пользователя страница 6

 

 

 

 

 

 

 

 

  

 

© Copyright 2015 TRENDnet. All Rights Reserved. 

 

 

 

4

 

 
TRENDnet User’s Guide

 

TV-IP430PI 

There  are  a  number  of  factors  involved  in  successful  camera  installation.  Follow  the 
suggested installation steps and go  through the check lists. This guide  will help  you to 
make your camera installation smooth and easy. 
 

 

Plan for installation location   

 

Setup Camera with CD 

 

Selecting the appropriate mounting accessories, see Mounting Guide

 

 
Plan for Installation 

 

Viewing angle 

 

The camera is a vari-focal camera with a wide viewing range that provides non-
distorted  and  detailed  images.  Choose  the  location  where  has  good  angle  to 
shoot the image you expect to see. The motion detection area should also be 
considered when installing the camera.  

 

Weather Conditions 

 

The  camera  is  an  outdoor  dome  camera,  which  fits  most  installations  indoor 
and outdoor. The camera can work under a wide range of weather conditions. 
For severe weather conditions. Using the camera in milder weather conditions 
will help extend the camera’s life and preserve the quality of the camera image.  

 

Moisture:

 Avoid damp or moist environments whenever you can. The  camera 

is  an  IP66  grade  water  proof  camera,  and  it  will  work  in moist  environments. 
However,  rain  may  affect  the  picture  quality,  especially  at  night,  water  may 
reflect the light from the infra-red illumination and degrade picture quality. 

 

Temperature: 

Camera works within a specified temperature range. Areas with 

severe  temperatures  should  be  avoided  when  installing  the  camera.  It’s 
recommended that you use an enclosure with a heater and blower if you  plan 
on using this camera outside of the specified temperature range. 

 

Sunlight:

  Avoid  direct  sun  light  exposure.  Direct  sun  light  will  damage  the 

image  sensor.  If  sunlight  is  necessary  for  your  viewing  purposes,  provide 
protection for the image sensor.  

 

Lighting: 

Consider installing your camera faces the same direction of the light 

sources.  Shooting  images  with  top-down  position  outdoor  or  next  to  the 
existing  light  source  are  good  choices.  Avoid  the  light  source  if  it  creates  a 
shade that darkens the viewing area.

 

 

Setup Camera with CD 

1.

 

Insert  the Installation CD-ROM into your computer’s  CD-ROM drive to initiate 
the  Auto-Run  program.    Choose  your  preferred  language  and  then  click  the

 

Install Camera

.  (mounting accessories are not included)  

  

  

        

 

 

 

 

Содержание TV-IP430PI



























































Отзывы:

Нет отзывов