TRENDnet TV-IP430PI Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 58

TRENDnet TV-IP430PI Скачать руководство пользователя страница 55

© Copyright 2015 TRENDnet. All Rights Reserved.

53

TRENDnet User’s Guide

TV-IP430PI

Federal Communication Commission Interference Statement

This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  Class  B  digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection  against  harmful  interference  in  a  residential  installation.  This  equipment
generates,  uses  and  can  radiate  radio  frequency  energy  and,  if  not  installed  and  used  in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.



Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.

IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.

Country Code selection feature to be disabled for products marketed to the US/CANADA

Europe – EU Declaration of Conformity

TRENDnet hereby declare that the product is in compliance with the essential requirements
and other relevant provisions under our sole responsibility.

EMC

EN 55022: 2010 Class A
EN 611000-3-2: 2006 + A1: 2009 + A2: 2009
EN 611000-3-3: 2013
EN 50130-4: 2011

This product is herewith confirmed to comply with the Directives.

Directives

EMC Directive 2004/108/EC

RoHS Directive 2011/65/EU

REACH Regulation (EC) No. 1907/2006

«
...
53
54
55
56
57
...
»

Содержание TV-IP430PI



























































Отзывы:

Нет отзывов