Trelawny SF11EX, Руководство по эксплуатации и обслуживанию

Страница: 9 / 16

www.trelawny.co.uk
machine storage
DISPOSAL
Short period storage: up to 3months.
Clean the outside of the machine and inspect the cutter heads
for wear, replace any worn parts as required. Insert a liberal
quantity of air tool oil through the air inlet and run briefly to
ensure that internal components are coated with oil. Cover the
machine to protect it: Store the machine in a dry place.
Long period storage: over 3months
Clean outside of machine, inspect the cutter heads for wear;
replace any worn parts as required. Remove any build up of
material from the cutter head area. Insert a liberal quantity
of air tool oil through the air inlet and run briefly to ensure
that internal components are coated with oil. Lubricate the
exposed part of the piston and cylinder. (See recommended
lubricants) Cover the machine to protect it: Store the machine
in a dry place. After a further 3 months have elapsed, insert
oil into the air inlet as previously described. When next used,
continue as per “Starting work section”.
Handle to Sub-frame
Fit washer (17) to bolt (16) and align all holes though chassis
and anti-vibration mountings (18) guide the bolt through until
it appears at the other end. Fit washer (17) to threaded end
of bolt and fit nut (15). To ensure that the sub-frame does
not twist or buckle through over tightening of the nyloc nut
(15), tighten so that not more than 3/8” (10mm) of thread it
protruding from the nyloc nut (15). Select a 13mm A/F spanner
to suit (8) and a 6mm A/F Allen key to suit caphead screw (9).
Slacken off both bolts (9) and nuts (8) align the lifting plate (10)
to the lifting block (12) and insert the locking pin (11). Ensure
that the pin hole is central and the locking pin can be removed
and inserted easily, adjust as necessary.
Ball Valve Mounting
Fit one of the two u-bolts (3) around ball valve (6) and through
bracket (4) so that the ball valve is in line with the handle tube.
Guide the u-bolt (3) into holes in the mounting flange so that
the ball valve is in line with the handle tube. Fit two nuts (5)
finger tight to hold the unit in place. Repeat with the second
u-bolt and bracket. Align the ball valve handle with the main
handle (14). Select a 13mm A/F spanner and fasten evenly the
four nuts (5) until the valve is secure.
Lifting Plate
Align holes in the lifting plate with the holes on that of the
lifting plate flange, ensuring that the position of the lifting plate
(10) is central to the main handle (14). Insert the bolt (9) and fit a
washer (8a) and nut (8). Fit the handle-locking pin (11).
Select a 13mm A/F spanner to suit (8) and a 6mm A/F Allen
key to suit caphead screw (9). Tighten both nut and bolts (8) &
(9) ensuring that the pin hole is central and the locking pin can
be removed and inserted easily.
Dismantle into component form, segregate according to
material composition and dispose of using waste recycling
processes specified by local regulations.
VERY IMPORTANT
Only Trelawny Beryllium Copper Heads must be used in
this tool. DO NOT substitute with any other head.
Machinery Directive Information
This tool has been designed and produced in accordance with
the following directives:
2006/42/EC Machinery Directive
and applicable harmonised standard: EN ISO 1 1148-4:2012
If your company has any problem with our products or would
like to discuss the possibility of an improvement being made
to them, then please do not hesitate to contact us. Your
comments are both important and appreciated.
The company operates a policy of continuous product
development and refinement and therefore reserves the
right to change technical specifications and product designs
without giving prior notice.
All rights reserved. Any unauthorised use or copying of
the contents or part thereof is prohibited. This applies to
trademarks, model denominations, part numbers and
drawings.
Use only genuine Trelawny spares. The use of non-Trelawny
spare parts invalidates the warranty and ATEX Certification.