Trek INCITE 6i Скачать руководство пользователя

Страница: 27 / 27

Limited Warranty

lIMITEd WARRANTy

Trek Bicycle Corporation warrants each new Incite computer

against defects in workmanship and materials.

This warranty covers

Trek Incite computer models 6i, 8i, 9i, 11i, ACH, and ACH Digital

for a period of two years from the date of sale.

This warranty does not cover

• Normal wear and tear, including the length of battery life
• Improper assembly
• Installation of parts or accessories not originally intended

for, or compatible with the component as sold

• Damage or failure due to accident, misuse, abuse, or neglect

This warranty is void in its entirety by any modification of the

component or its parts.

This warranty is expressly limited to the repair or replacement of a

defective item and is the sole remedy of the warranty. This warranty

extends from the date of purchase, applies only to the original owner, and

is not transferable. Trek is not responsible for incidental or consequen-

tial damages. Some states do not allow the exclusion of incidental or

consequential damages, so the above exclusion may not apply to you.

Claims under this warranty must be made through an authorized dealer.

Proof of purchase is required.

This warranty gives the consumer specific legal rights, and those rights

may vary from place to place. This warranty does not affect the statutory

rights of the consumer.

Содержание INCITE 6i




























Результаты поиска

Содержание INCITE 6i

Отзывы:

Похожие инструкции для INCITE 6i

Бренды по названию

Популярные бренды

Trek INCITE 6i, Руководство пользователя

Результаты поиска

Содержание INCITE 6i

Отзывы:

Похожие инструкции для INCITE 6i

Бренды по названию

Популярные бренды