Trek INCITE 6i Скачать руководство пользователя

Страница: 26 / 27

Setting Custom Wheel Size

Figure 8- Measuring rollout for

wheel size

To measure rollout for wheel size

Table 1 approximates the circumfer-

ence of each tire size. Instead of using

an approximation, you can measure the

actual circumference of your wheel. You

need a helper, your bike, and a smooth

floor with enough room to roll the bike

about 7 feet (245 cm) in a straight line.

1. With the valve stem of the front wheel

directly over the floor Figure 18), sit on

the bike.

2. Have your helper mark the floor at the

valve stem.

3. While you sit on the bike, have the helper roll the bike forward

one revolution of the wheel, so that the valve stem is again

directly over the floor.

4. Mark the new location of the valve stem.
5. Measure the distance between the marks, in millimeters.

If you can only measure in inches, convert to millimeters by multiplying

by 25.4.

6. Use the result to program your computer, following the instruc-

tions on page 22.

Содержание INCITE 6i




























Результаты поиска

Содержание INCITE 6i

Отзывы:

Похожие инструкции для INCITE 6i

Бренды по названию

Популярные бренды

Trek INCITE 6i, Руководство пользователя

Результаты поиска

Содержание INCITE 6i

Отзывы:

Похожие инструкции для INCITE 6i

Бренды по названию

Популярные бренды