background image

E-REVO BRUSHLESS • 13

Spring Clip Installation

1. Insert the two tabs on 

the spring clip into the 
rectangular tab slots in 
the chassis.

2. Rotate the spring clip 

upward.

3. Snap the tabs into place.
Many LiPo batteries do not use a hard plastic case.  If using LiPo 
batteries that do not have a hard case, always be sure to use the foam 
rubber cushion in the front of the battery compartment.  

Do not use 

the battery retainer tabs in the front of the battery compartments 
when using LiPo batteries that are not in a hard plastic case. 

A hard 

front impact or crash when driving can damage the LiPo batteries.

RADIO SYSTEM RULES

• Always turn your TQi transmitter on first and off last. This procedure 

will help to prevent your model from receiving stray signals 
from another transmitter, or other source, and running out of 
control. Your model has electronic failsafes to prevent this type of 
malfunction, but the first, best defense against a runaway model is 
to always turn the transmitter on first, and off last.

• Always use new batteries for the radio system. 

Weak batteries will 

limit the radio signal between the receiver and the transmitter.

 Loss 

of the radio signal can cause you to lose control of your model.

• In order for the transmitter and receiver to bind to one another, 

the receiver in the model must be turned on within 20 seconds 
of turning on the transmitter. The transmitter LED will flash fast 
red indicating a failure to link. If you miss it, simply turn off the 
transmitter and start over.

• Always turn on the transmitter before plugging in the battery.

RADIO SYSTEM BASIC ADJUSTMENTS

Throttle Neutral Adjustment 

The throttle neutral adjustment is located on the 
transmitter face and controls the forward/reverse 
travel of the throttle trigger. Change the adjustment 
by pressing the button and sliding it to the desired 
position. There are two settings available:

50/50

: Allows equal travel for both acceleration and reverse.

70/30

: Allows more throttle travel (70%) and less reverse travel (30%).

Note: We strongly recommend to leave this control in its factory 
location until you become familiar with all the adjustments and 
capabilities of your model. 

To change the throttle neutral adjust 

position, turn the transmitter off before adjusting the neutral position. 

You will need to reprogram your electronic speed control to 
recognize the 70/30 setting.

 Turn to page 16 for instructions.

Steering Trim 

The electronic steering trim located on the 
face of the transmitter adjusts the neutral 
(center) point of the steering channel. 

Note: 

Traxxas Stability Management (TSM) must be completely 

turned off while adjusting steering trim. See page 15 for TSM 
adjustments.

TRAXXAS TQ

i

 RADIO SYSTEM

5

RADIO SYSTEM 

CONTROLS

Always turn your

transmitter on first.

Turn on the model.

1

2

Plug in the batteries.

3

Stop immediately at the first 
sign of weak batteries. Never 
turn the transmitter off when 
the battery pack is plugged 
in. The model could run out 
of control.

Remember, always turn the 
TQi transmitter on first and 
off last to avoid damage to 
your model. 

Forward

Neutral

Brake/Reverse

TURN

 R

IG

H

T

T

U

R

N

 LE

FT

Содержание 56086-4







































Отзывы: