background image

Press MENU 

to move through options. 

Press SET 

to select an option.

Press MENU 

to move through options. 

Press SET 

to select an option.

Press SET 

to select an option.

Enter Programming

Press and hold 
MENU for 3 seconds 

Steering Sensitivity (Expo)

One Blink Red

1

Electric

One Blink Red

1

Unlock

One Blink Red

1

Servo Reversing

One Blink Red

1

Servo Reversing

One Blink Red

1

Confirm Deletion

One Blink Red

1

Multi-Function Knob

One Blink Green

1

Channel Setup

Two Blinks Green

2

Mode Selection

Three Blinks Green

3

Traxxas-Link

Four Blinks Green

4

Steering (Channel 1)

One Blink Green

1

Model Locking

One Blink Green

1

Throttle (Channel 2)

Two Blinks Green

2

Delete Model

Two Blinks Green

2

Throttle Sensitivity (Expo)

Two Blinks Red

2

Nitro

Two Blinks Red

2

Lock

Two Blinks Red

2

Sub-Trim

Two Blinks Red

2

Sub-Trim

Two Blinks Red

2

Steering % (Dual-Rate)

Three Blinks Red

3

Unlock All

Three Blinks Red

3

End Points

Three Blinks Red

3

Braking % 

Four Blinks Red

4

Reset End Points

Four Blinks Red

4

Throttle Trim

Five Blinks Red

5

Knob Disabled

Six Blinks Red

6

Press 

MENU

Press 

MENU

Press 

MENU

Press 

SET

Press 

SET

Press 

SET

Press 

SET

Press 

SET

Press 

SET

Press 

SET

Press SET to reverse 
servo direction.

Press SET to reverse 
servo direction.

Press SET to restore factory 
default end points.

Reset End Points

Four Blinks Red

4

Press SET to restore factory 
default end points.

Use knob to adjust  
sub-trim. Press SET to save.

Use knob to adjust sub-
trim. Press SET to save.

Use steering wheel to 
adjust. Turn right to desired 
end point, press set to save. 

Turn left to desired end point and press set to save.  
To reset max throw: Let go of controls and press SET.

Note: The transmitter is “live” during programming 
so you can test the settings real time without having 
to exit the Menu Tree.

End Points

Three Blinks Red

3

Use trigger to adjust. Pull 
back to desired end point, 
press set to save. Push 

forward to desired end point and press set to save.  
To reset max throw: Let go of controls and press SET.

The Menu Tree below shows how to navigate through 
the TQi transmitter’s various settings and functions. 
Press and hold MENU to enter the Menu Tree, and use 
the following commands to navigate through the menu 
and select options. 

MENU:

  When you enter a menu, you always start at the 

top. Press MENU to move down the Menu Tree. 
When you reach the bottom of the tree, pressing 
MENU again will return you to the top.

SET:

   Press SET to move across the Menu Tree and select 

options. When an option is committed to the 
transmitter’s memory, the status LED will rapidly 
blink green.

BACK:

   Press both MENU and SET to go back one level in 

the Menu Tree.

EXIT:

   Press and hold MENU to exit programming.  

Your selected options will be saved.

ECHO:

   Press and hold SET to activate the “echo” function. 

Echo will “play back” your current position on the 
Menu Tree should you lose your place. For example: 
If your current position is Steering Channel End 
Points, holding SET will cause the LED to blink green 
twice, green once, and then red three times. Echo 
will not alter your adjustments or change your 
position in the programming sequence. 

MENU TREE

Below is an example of how to access a function in the Menu 
Tree. In the example, the user is setting the Multi-Function knob 
to be a Steering % (Dual-Rate) control.

To set the Multi-Function knob to control STEERING % (DUAL-RATE):

1. Switch the transmitter on.
2. Press and hold MENU until the green LED lights. It will blink in single 

intervals.

3. Press SET. The red LED will blink in single intervals to indicate Steering 

Sensitivity (Expo) has been selected.

4. Press MENU twice. The red LED will blink three times repeatedly to 

indicate Steering % (Dual-Rate)  has been selected.

5. Press SET to select.  The green LED will blink 8 times fast to indicate 

successful selection.

6. Press and hold MENU to return to driving mode. 

Restoring Factory Defaults:

Transmitter 

OFF

Hold both 

MENU and SET

Transmitter 

ON

Release MENU and SET  

red LED blinks

  

Press SET 

to clear settings. LED will turn 

solid green. Transmitter is restored to default

Press 

SET

Torque Control*

Seven Blinks Red

7

TSM

Eight Blinks Red

8

Press MENU

Press MENU

*Torque Control is a feature designed only for use with the power system in the Traxxas Funny Car Race Replica (Model #6907).

Press 

MENU

TQ

i

 ADVANCED TUNING GUIDE

Содержание 56086-4







































Отзывы: