background image

24 • E-REVO BRUSHLESS

MOTORS AND GEARING

CAUTION: Read before operating your model with 65+mph 
gearing!

• The 24/54 ratio for use with 6S LiPo batteries is designed 

for maximum speed on smooth surfaces only, with steady 
acceleration to full throttle. 

• Do not use this gear ratio for general driving. 
• Avoid repetitive starting and stopping. 
• Do not use the 24/54 ratio with NiMH batteries or low-capacity 

LiPo batteries. 5000mAh LiPo batteries are recommended.

• Allow the motor to cool between runs, and monitor motor 

temperature. 

• Do not use the 24/54 gear ratio for off-road running or 

overheating and damage may result. 

• Do not allow the motor temperature to exceed 200° F or damage 

and motor failure may result. To accurately monitor motor 
temperature and prevent overheating, a telemetry temperature 
sensor (part #6521, sold separately) can be installed on the motor 
to continually monitor temperature as your drive.

Adjusting Gear Mesh

Incorrect gear mesh is the most common 
cause of stripped spur gears. Gear mesh 
should be checked and adjusted anytime 
a gear is replaced. Access the gears by 
removing the single screw on the top 
gear cover.

To set the gear mesh, cut a narrow strip of 
notebook paper and run it into the gear 
mesh of the motor. The motor is mounted 
to an aluminum motor mount. 
Loosen the single motor mount 
screw with the provided 3mm 
wrench to slide the motor 
mount. Slide the motor and 
pinion gear into the spur gear. 
Retighten the motor mount 
screw and then remove the 
strip of paper.  You should be 
able to run a fresh strip of paper 
through the gears without binding them.

Gearing Compatibility Chart:

The chart below shows a full range 
of gear combinations. This does NOT 
imply that these gear combinations 
should be used. Over-gearing 
(bigger pinions, smaller spurs) can 
overheat and damage the motor 
and/or speed control. 

BASIC TUNING ADJUSTMENTS

54

56

58

62

65

68

12

4.50 4.67 4.83 5.17 5.42 5.67

13

4.15 4.31 4.46 4.77 5.00 5.23

14

3.86 4.00 4.14 4.43 4.64 4.86

15

3.60

3.73 3.87 4.13 4.33 4.53

16

3.38 3.50

3.63 3.88 4.06 4.25

17

3.18 3.29 3.41

3.65 3.82 4.00

18

3.00

3.11 3.22 3.44

3.61

3.78

19

NR

NR

3.05 3.26 3.42 3.58

20

NR

NR

NR

3.10 3.25 3.40

21

NR

NR

NR

NR

3.10 3.24

22

NR

NR

NR

NR

NR

3.09

23

NR

NR

NR

NR

NR DNF

24

NR

NR

NR

NR

NR DNF

25

NR

NR

NR

NR

NR DNF

Pinion Gear

Spur Gear

Stock gearing

B

Optional included gearing (4S LiPo)

B

Recommended gearing 
for 4S LiPo only

Not recommended

Does not fit

Recommended gearing 
for all battery types

Motor Mount 

Screw

Strip of Paper

Speed

35+ mph

40+ mph*

50+ mph

65 mph

& Beyond

Pinion/Spur

18/65

18/54

18/65

24/54

**

Battery

Twin 7-Cell NiMH

(14 cell total)

Twin 2S LiPo

(4S total)

Twin 3S LiPo

(6S total)

Twin 3S LiPo

(6S total)

Nominal Voltage

16.8V

14.8V

22.2V

22.2V

mAh

4000+ mAh

5000+ mAh

5000+ mAh

5000+ mAh

Skill Level

Your Battery Selection and Pinion Gear   
Selection Determines Your Speed.  

 How Fast Do You Want To Go?

For Expert Drivers

For Expert Drivers

*with included optional gearing
**optional gearing (not included)

Model #56086-4

Содержание 56086-4







































Отзывы: