Transducer Techniques LCA-9PC Скачать руководство пользователя страница 2

Страница: 2 / 18

TABLE OF CONTENTS

PRODUCT DESCRIPTION ................................................................................... 3

MOUNTING PROVISIONS .................................................................................... 3

SETUP USING JUMPERS & POTENTIOMETERS ............................................... 4

ELECTRICAL CONNECTIONS ............................................................................. 7

CALIBRATION ....................................................................................................... 10

OPERATING RECOMMENDATIONS ................................................................... 12

SPECIFICATIONS ................................................................................................. 13

CASE DIMENSIONS ............................................................................................. 15

TROUBLESHOOTING........................................................................................... 15

CIRCUIT BOARD DIMENSIONS ........................................................................... 16

ACCESSORIES ..................................................................................................... 17

WARRANTY / REPAIR POLICY ............................................................................ 18

Revised November 2019

Содержание LCA-9PC


















