background image

® U.S. Registered Trademark
Copyright © American Standard Inc. 1999

INSTALLER'S GUIDE

XT300C Deluxe Programmable

Heat-Cool Thermostat

18-HD25D1-3

APPLICATION

The XT300C Deluxe Programmable Heat-Cool Thermostat provides electronic control of 24 Vac single-stage heating and
cooling systems. Refer to Table 1 for a general description of the thermostat. This thermostat is powered by the heating system
only. Refer to Wiring for information on wiring for cooling-only applications.

Table 1. Description of XT300C

RECYCLING NOTICE

If this thermostat is replacing a thermostat that contains
mercury in a sealed tube, do not place your old
thermostat in the trash.

Contact your local waste management authority for
instructions regarding recycling and the proper
disposal of the old thermostat.

INSTALLATION

When Installing this Thermostat...

1. Read these instructions carefully. Failure to follow the

instructions can damage the product or cause a
hazardous condition.

2. Check the ratings given in the instructions and on the

product to make sure the product is suitable for your
application.

3. Installer must be a trained, experienced service

technician.

4. After completing installation, use these instructions

to check out the product operation.

Location

Install the thermostat about 5 ft (1.5m) above the floor in an
area with good air circulation at average temperature. See
Fig. 1. Avoid installing the thermostat where it can be affected
by the following:

Drafts, or dead spots behind doors and in corners.

Hot or cold air from ducts.

Radiant heat from sun or appliances.

Concealed pipes and chimneys.

Unheated (uncooled) areas such as an outside wall
behind the thermostat.

Wallplate Installation

Position wallplate horizontally on the wall or on a 2 in. x 4 in.
wiring box.

1. Position and level the wallplate for appearance only (the

thermostat will function properly even when
not level).

Fig. 1. Typical location of thermostat.

5 FEET

[1.5 METERS]

YES

NO

NO

NO

M17106

69-1212-1

Model

System

Changeover

System  
Selection

Fan
Selection

Comments

XT300C Heat-Cool

Automatic

Heat-Off-Cool -

Auto

On-Auto

System and fan selections are done by
keyboard.

Содержание XT300C













Отзывы: