Trane X1379088401 Скачать руководство пользователя страница 22

22

BAS-SVX17B-EN

Operation

 

Temporary Override Set-up (CV/HP only)

To override a setting for a specified period of time, start at the home screen and proceed 
as follows:

The heating setpoint symbol 

flashes when selected.

The cooling setpoint symbol 

flashes when selected.

The override symbol flashes 

throughout the temporary 

override set-up operation.

1.

Press 

 or 

. The current temperature setpoint 

appears.

2. Within 5 seconds of 

Step 1

, press 

 to raise the 

setpoint or 

 to lower the setpoint. The thermostat 

enters timed override mode, giving you the 
opportunity to specify the other parameters of the 
override.

The override symbol flashes, and continues 
flashing throughout the procedure. 

Either the heating or cooling setpoint symbol 
flashes.

Note:

The current zone temperature determines whether 
the heating or cooling setpoint symbol appears first.

3. Press   or 

 to toggle between the heating and 

cooling setpoints.

4. Press 

 or 

 to increase or decrease the heating 

or cooling setpoint.

The fan setting flashes when 

selected.

5. To override the fan setting, press 

 (if starting from 

the heating setpoint, press twice). Press   or 

 to 

change between Auto and On.

Note:

Only if the programmable fan option is enabled.

The time setting for override 

set-up.

6. Press 

 to specify the amount of time the override 

lasts. Press 

 or 

 to select the number of hours. 

If your override time is over 23 hours, press   or 

 to 

select days. Press 

 or 

 to select the number of 

days.

The occupancy setting flashes 

when selected.

7. To override occupancy, press 

 (if starting from 

days, press twice). The occupancy symbol flashes. 
Press   or 

 to change between occupied and 

unoccupied.

The temporary override 

symbol appears on the display 

and stays on while an override 

is present.

8. To confirm your override settings, press 

 and hold 

2 seconds, or wait 15 seconds. The home screen 
appears with the override symbol on it.

Note:

To delete override settings, select temporary override 
set-up and press the Test/Configuration button. The 
home screen appears without the override symbol.

DAYS

HOURS

Содержание X1379088401

































Отзывы: