Trane Voyager Commercial, Инструкция по установке, эксплуатации и обслуживанию

Страница: 66 / 156

66 RT-SVX34R-EN
Preparing the Unit for Operation
Be sure to complete all of the procedures described in
this section before starting the unit for the first time.
Use the checklist provided below in conjunction with
the “Installation Checklist” to ensure that the unit is
properly installed and ready for operation.
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss V Vo olltta ag ge e!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err b be effo orre e sse errv viicciin ng g cco ou ulld d
rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss iin njju urry y..
D Diisscco on nn ne ecctt a allll e elle eccttrriicc p po ow we err,, iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne eccttss b be effo orre e sse errv viicciin ng g.. F Fo ollllo ow w p prro op pe err
llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o e en nssu urre e tth he e p po ow we err
cca an n n no ott b be e iin na ad dv ve errtte en nttlly y e en ne errg giizze ed d.. V Ve erriiffy y tth ha att n no o
p po ow we err iiss p prre esse en ntt w wiitth h a a v vo ollttm me ette err..
• Check all electrical connections for tightness and
“point of termination” accuracy.
• Verify that the condenser airflow will be
unobstructed.
• Check the compressor crankcase oil level. Oil
should be visible in the compressor oil sight glass.
The oil level may be above the sight glass prior to
the initial start. Use appropriate lighting (flashlight)
to verify the presence of oil.
• Prior to unit startup allow the crankcase heater to
operate a minimum of 8 hours to remove liquid
refrigerant from the compressor sump.
• Optional Service Valves - Verify that the discharge
service valve and suction service valve fully open
on each circuit.
N No otte e:: High Efficiency units come standard with
discharge service valves.
• Check the supply fan belts for proper tension and
the fan bearings for sufficient lubrication. If the
belts require adjustment, or if the bearings need
lubricating, refer to the Maintenance section of this
manual for instructions.
• Inspect the interior of the unit for tools and debris
and install all panels in preparation for starting the
unit.
Electrical Phasing
Unlike traditional reciprocating compressors, scroll
compressors are phase sensitive. Proper phasing of the
electrical supply to the unit is critical for proper
operation and reliability.
The compressor motor is internally connected for
clockwise rotation with the incoming power supply
phased as A, B, C. Proper electrical supply phasing can
be quickly determined and corrected before starting the
unit by using an instrument such as an Ideal - Sperry
61-520 Phase Sequence Indicator and following the
steps below:
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss V Vo olltta ag ge e!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err b be effo orre e sse errv viicciin ng g cco ou ulld d
rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss iin njju urry y..
D Diisscco on nn ne ecctt a allll e elle eccttrriicc p po ow we err,, iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne eccttss b be effo orre e sse errv viicciin ng g.. F Fo ollllo ow w p prro op pe err
llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o e en nssu urre e tth he e p po ow we err
cca an n n no ott b be e iin na ad dv ve errtte en nttlly y e en ne errg giizze ed d.. V Ve erriiffy y tth ha att n no o
p po ow we err iiss p prre esse en ntt w wiitth h a a v vo ollttm me ette err..
• Open the disconnect switch or circuit protector
switch that provides the supply power to the unit's
power terminal block or to the unit mounted
disconnect switch.
• To be consistent with the compressor leads,
connect the phase sequence indicator leads to the
terminal block or unit mounted disconnect switch
as follows;
Table 40. Phase sequence leads
Phase Sequence Leads
Unit Power Terminal
Red (phase A)
L1
Blue (phase B)
L2
Black (Phase C)
L3
• Turn the “System” selection switch to the “Off”
position and the “Fan” selection switch (if
Applicable) to the “Auto” position.
• Close the disconnect switch or circuit protector
switch that provides the supply power to the unit's
power terminal block or unit mounted disconnect
switch.
W WA AR RN NIIN NG G
L Liiv ve e E Elle eccttrriicca all C Co om mp po on ne en nttss!!
F Fa aiillu urre e tto o ffo ollllo ow w a allll e elle eccttrriicca all ssa affe etty y p prre ecca au uttiio on nss
w wh he en n e ex xp po osse ed d tto o lliiv ve e e elle eccttrriicca all cco om mp po on ne en nttss cco ou ulld d
rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss iin njju urry y..
W Wh he en n iitt iiss n ne ecce essssa arry y tto o w wo orrkk w wiitth h lliiv ve e e elle eccttrriicca all
cco om mp po on ne en nttss,, h ha av ve e a a q qu ua alliiffiie ed d lliicce en nsse ed d e elle eccttrriicciia an n
o orr o otth he err iin nd diiv viid du ua all w wh ho o h ha ass b be ee en n p prro op pe errlly y ttrra aiin ne ed d
iin n h ha an nd dlliin ng g lliiv ve e e elle eccttrriicca all cco om mp po on ne en nttss p pe errffo orrm m
tth he esse e tta asskkss..
HIGH VOLTAGE IS PRESENT AT TERMINAL BLOCK
HTB1 OR UNIT DISCONNECT SWITCH.
• Observe the ABC and CBA phase indicator lights on
the face of the sequencer. The ABC indicator light
will glow if the phase is ABC. If the CBA indicator
light glows, open the disconnect switch or circuit
protection switch and reverse any two power wires.
• Restore main electrical power and recheck phasing.
If the phasing is correct, open the disconnect switch
or circuit protection switch and remove the phase
sequence indicator.
S Stta arrttu up p