background image

11

Unit Operation

In Occupied mode, the controller 
operates according to the occupied 
setpoints. In Occupied Standby 
Mode, the unit controller operates 
according to the Occupied Standby 
setpoints. When the controller 
receives a communicated 
unoccupied request, the controller 

operates according to the 
unoccupied setpoints regardless of 
the state of the hardwired 
occupancy input.

If neither the binary input nor the 
communicated input is used to 
select the occupancy mode, the 

controller defaults to occupied 
mode because the occupancy binary 
input (if present) typically is 
configured as normally open 
without an occupancy device 
connected.

Table 4

: Normally open hardwired input configuration (BI 3)

Description

Communicated Request

Hardwired State

Result

Standalone

NA

Open = Occupied

Occupied

Standalone

NA

Closed = Unoccupied

Unoccupied

Communicating

Occupied

Open = Occupied

Occupied

Communicating

Unoccupied

Open = Occupied

Unoccupied

Communicating

Occupied Standby

Open = Occupied

Occupied Standby

Communicating

Occupied

Closed = Occupied Standby

Occupied Standby

Communicating

Unoccupied

Closed = Occupied Standby

Unoccupied

Communicating

Occupied Standby

Closed = Occupied Standby

Occupied Standby

Generic Binary Input

Building automation systems can 
monitor the status of the generic 
binary input. This input does not 
affect controller operation.

High and Low Pressure
Switches

The high and low pressure cutout 
switches are wired in series with the 
compressor contactor in the unit. 
The ZN510 controller detects the 
state of each switch circuit by 
monitoring the controller’s 
compressor triac outputs. If either 
the high pressure switch (HPC) or 
the low pressure switch (LPC) switch 
opens, a fault condition occurs. This 
open circuit prevents the 

compressor contactor from 
energizing keeping the compressor 
from running. The controller 
automatically detects the fault 
condition by measuring the 
compressor triac output signal.

By default, when the HPC or LPC 
switches detect a high or low 
pressure condition in the refrigerant 
circuit, the special input detects the 
diagnostic and disables all 
compressor operation for that 
circuit. The unit fan continues to 
operate, if only one circuit is 
disabled in a two compressor unit. 
When the HPC/LPC diagnostic is 
present on both circuits, the ZN510 
shuts off the unit fan and disables 

unit operation. See 

Figure 7

 for high 

and low pressure switch.

When the refrigerant circuit returns 
to normal, the HPC and the LPC 
switches automatically reset. The 
high or low pressure cutout 
diagnostic may need to be manually 
reset to clear the diagnostic and 
enable compressor operation for the 
fault circuit.

Note:
If configured for normally closed, all states are opposite of Table 4.

Содержание Tracer ZN510

































Отзывы: