background image

X-XX UL

INSTALLATION INSTRUCTIONS

Electronic

Heat Pump Thermostat

TAYSTAT 575

APPLICATION

The TAYSTAT 575 Electronic Heat Pump Thermostat provides electronic control of 24 Vac, two speed or two com-
pressor heat pump systems with auxiliary heat. The TAYSTAT 575 can be configured to operate a single compressor
heat pump system. Refer to Table 1 for a general description of the thermostat. All TAYSTAT 575 Thermostats require
a common wire to supply power.

Table 1. TAYSTAT 575 Thermostat Description.

MERCURY NOTICE

If this control is replacing a control that contains
mercury in a sealed tube, do not place your old
control in the trash. Dispose of properly.

Contact your local waste management authority for
instructions regarding recycling and the proper
disposal of the old control.

INSTALLATION

When Installing this Product...

1. Read these instructions carefully. Failure to follow

the instructions can damage the product or cause a
hazardous condition.

2. Check the ratings given in the instructions and on

the product to make sure the product is suitable for
your application.

3. Installer must be a trained, experienced service

technician.

4. After completing installation, use these instructions

to check out the product operation.

CAUTION

Electrical Shock or Equipment Damage Hazard.
Can shock individuals or short
equipment circuitry.
Disconnect power supply before installation.

Location

Install the thermostat about 5 ft (1.5m) above the floor in
an area with good air circulation at average temperature.
See Fig. 1.

Do not install the thermostat where it can be affected by:

drafts, or dead spots behind doors and in corners.

hot or cold air from ducts.

radiant heat from sun or appliances.

concealed pipes and chimneys.

unheated (uncooled) areas such as an outside wall
behind the thermostat.

®U.S. Registered Trademark.  •            •   All Rights Reserved

Pub. No. 11-HD28D2-1

69-1591-1

TAYSTAT   Changeover

                                         

System Selection

Fan

Selection

Comments

575

Automatic

Em. Ht. – Heat-Off-Auto-Cool

On-Auto

Down-selectalbe for single compressor
systems.

Содержание TAYSTAT 575













Отзывы: