Trane IC-IH 039 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 48

background image

RT-SVX056D-GB

19

Installation

General information: The installation must conform to
all local standards and regulations.

Reception of Units

Unit Handling

The unit is supplied on wooden blocks. It is
recommended to check the machine’s condition upon
reception.
There are two ways to handle the unit:
1. Handle the machine using a forklift, in accordance

with applicable safety regulations. Handling of the
unit is prohibited unless forks are longer than the
length of the unit (not recommended as there is a
risk of damage if not done carefully).

2. Use a lifting beam correctly adjusted to fit the unit

(recommended).

The units are supplied on the truck but are not
unloaded. A lifting lug is provided on each corner of the
unit’s base to facilitate handling. 4 shackles and 4 slings
are required.
Use a lifting beam to prevent the cables pressing too
hard on top of the unit during lifting.

Important:

For unit to fit on the roof curb the wooden

blocks must be removed.

Lifting and moving Instructions

Specific lifting method is recommended as follows:
1 - The units are supplied with four lifting points
2 - Slings and spreader bar to be provided by rigger and

attached to the four lifting points.

3 - Minimum rated lifting capacity (vertical) of each

sling and spreader bar shall be no less than the unit
shipping weight.

4 - Caution: The unit must be lifted with the utmost care.

Avoid shock load by lifting slowly and evenly.

5 - Remove slings and spreader bars when installation is

completed.

The detailed handling, lifting instructions including
all weights and sling lengths are given on the specific
drawings and instructions shipped with the unit.

Roof Curb Installation

Roof curbs are available as an accessory for “downflow”
units to support the unit and ensure the water tightness
between the rooftop and the roof. Four types of
roofcurbs are available: the standard version to allow the
installation of the unit on a flat roof with different return
flow patterns (return roofcurb down, return roofcurb
horizontal, multidirectional roofcurb) and the adjustable
version for a slope roof installation (adjustable roofcurb
down). The roofcurb characteristic is given in roofcurb
submittal drawings sent with the unit.

Figure 2 - Roofcurb down

Figure 3 - Roofcurb multidirectional assembly

«
...
17
18
19
20
21
...
»

Содержание IC-IH 039

















































Отзывы:

Нет отзывов

Похожие инструкции для IC-IH 039

Бренд: B-TEC Страницы: 11

Бренд: MCS Master Страницы: 203

Бренд: Barnes Страницы: 16

Бренд: Honda Страницы: 75

CHAUFFAGE FRANCAIS LEXIA 500W

Бренд: SANNOVER Страницы: 56

Бренд: Lumax Страницы: 28

Бренд: Tallas Страницы: 68

Бренд: Beckett Страницы: 2

Бренд: HOMCOM Страницы: 8

Бренд: Versonel Страницы: 12

Бренд: ABS Страницы: 10

Бренд: NAVAC Страницы: 8

Бренд: UNITED Страницы: 4

Бренд: Sears Страницы: 8

Бренд: Peraqua Страницы: 60

Бренд: PCE Instruments Страницы: 16

Бренд: Sovelor Страницы: 16

Бренд: Serene Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды