manualshive.com logo in svg

Trane CeilAir CW, Инструкция по установке, эксплуатации и обслуживанию, Страница: 47 / 52

Поделиться
Скачать
Trane CeilAir CW Скачать руководство пользователя страница 47

Maintenance

AH-SVX008C-EN

47 

•

Date of Order

•

Stated Part Price

•

Customer Billing Address

•

Shipping Address

•

Customer’s Telephone and Fax Numbers

•

Contact  Name

•

Unit Model No., Serial No. and Item No.

The customer is responsible for the shipping cost incurred 
for returning the defective part(s). Return of defective 
part(s) must be within 30 days at which time an evaluation 
of the part(s) is conducted and if the part is found to have 
a manufacturing defect a credit will be issued.

When returning defective part(s), complete the Return 
Material Authorization Tag and the address label provided 
with the replacement part. For prompt processing, please 
affix the RMA in a prominent place on the external 
packaging of the returned part.

Obtaining Spare/Replacement Parts

Maintaining a recommended spare parts inventory is an 
industry best practice for critical facilities. Onsite spares 
kits reduce downtime and can eliminate the cost of 
expedited freight charges.

Содержание CeilAir CW





















































Отзывы:

Нет отзывов