manualshive.com logo in svg

Trane CeilAir CW, Инструкция по установке, эксплуатации и обслуживанию, Страница: 46 / 52

Поделиться
Скачать
Trane CeilAir CW Скачать руководство пользователя страница 46

Maintenance

46

 AH-SVX008C-EN

replacement cylinder must be installed. The cylinder is 
disposable and cylinder life is dependent on water supply 
conditions and humidifier usage. Refer to the humidifier 
operator's manual supplied under separate cover for 
detailed instructions on changing the cylinder. The 
following procedures are to be followed when replacing 
the cylinder.

NOTICE

Humidifier Damage!

Failure to replace the cylinder at the end of cylinder life 
may result in humidifier damage.

Note:

Decrease the humidity setpoint below ambient 
humidity to allow the cylinder to cool down before 
removing the cylinder.

1. If your unit is equipped with an E² controller, turn the 

A/C unit off by pressing and holding the Enter key.

2. Turn off the water supply to the humidifier.

3. Turn the main power disconnect switch on the electric 

box to the Off position. Remove the cover from the 
electric box.

4. Using a pair of vise grips, turn the shaft of the main 

power switch to the On position to provide power for 
the humidifier drain solenoid.

5. Follow the steps of the cylinder replacement procedure 

in the humidifier installation and operation manual 
sent under separate cover with your unit.

6. Replace the cover on the electric box and turn the main 

power disconnect switch to the On position.

7. If your unit is equipped with an E² controller, turn the 

A/C unit on by pressing the Enter key.

8. Readjust the humidity to the desired setpoint.

If the humidifier is to be shut down for an extended period, 
follow the steps of the Extended Shutdown procedure in 
the humidifier installation and operation manual.

NOTICE

Cylinder Damage!

Failure to perform the recommended Extended 
Shutdown procedure before a prolonged shut-down 
period will drastically shorten the cylinder life.

Air Filter Replacement

The air filters are located either internal or external to the 
cabinet, depending on the configuration of the unit. 
Regardless of location, the filter is accessed through an 
access panel labeled "FILTER ACCESS". Remove the 
access panel and old filter. Ensuring directional airflow 
arrows on filter are correct, insert the new filter and replace 
the access panel. 

Product Support

Product Support provides aftermarket technical and field 
support, warranty authorization and part sales to 
contractors and end users. Factory authorized services are 
available by request and include:

•

Factory Authorized Start-up/Warranty Inspection

•

Commissioning Assistance

•

Break Fix Repair

•

Preventive Maintenance Contracts

•

Performance Evaluations

•

Technician and Owner Training

Factory Authorized Start Up/Warranty 
Inspection

Factory Authorized Start Up/Warranty Inspection ensures 
that your equipment is installed and operating per 
recommended guidelines. This essential service 
guarantees that equipment has the best warranty 
coverage available.

precision cooling equipment is covered by an industry 
leading 24 Month Upgraded Parts Warranty and 90 Day 
Labor Warranty once Factory Authorized Warranty 
Inspection/Start-Up is performed and start up checklists 
are returned and validated by product support.

A Limited 12 Month Parts Only Warranty applies if Factory 
Authorized Start Up/Warranty is not purchased and start 
up checklists are received from an unauthorized party and 
validated by product support.

Technical Support

When calling to obtain support, it is important to have the 
following information readily available, (information is 
found on the unit’s nameplate):

•

Unit Model Number

•

Sales Order Number

•

Item Number

•

Unit  Serial  Number

•

Description of Problem

Obtaining Warranty Parts

A support technician will provide troubleshooting 
assistance over the telephone.

If it can be determined that a part may be defective, a 
warranty authorization for a replacement part will be 
processed by Technical Support. The replacement part will 
then be shipped via UPS ground. If the customer requests 
that warranty part(s) be sent by any other method than 
UPS ground, the customer is responsible for the shipping 
charges.

The purchase order must contain the following items:

•

Purchase Order Number

Содержание CeilAir CW





















































Отзывы:

Нет отзывов