manualshive.com logo in svg

Trane CeilAir CW, Инструкция по установке, эксплуатации и обслуживанию, Страница: 20 / 52

Поделиться
Скачать
Trane CeilAir CW Скачать руководство пользователя страница 20

Installation

20

 AH-SVX008C-EN

drain line must be located so it will not be exposed to 
freezing temperatures. The drain line should be the full 
size of the connection. See the installation drawing 
provided with your unit for the size and location of the 
condensate drain line.

NOTICE

Coil Fins Damage

Do not use chloride-based water conditioning additives 
in the condensate drain pans. They cause corrosion on 
the coil fins.

Important:

Properly size and vent the P-trap according 
to applicable codes and best practices. 

Note:

During normal operation the optional humidifier 
drains hot water into the condensate drain line. As 
an option, a separate drain line may be provided for 
the humidifier.

Condensate Pump

A condensate pump (see figure below) is used to 
automatically remove condensate from the air conditioner 
and flush water from the humidifier (if applicable). A P-trap 
is installed for proper condensate drainage. The height of 
the trap is a minimum of 2 in. on most standard systems 
to ensure proper water drainage of the drain pan. The 
condensate pump discharge line should be 1/2 in. I.D. 
(maximum) vinyl tubing or 1/2 in. O.D. (maximum) copper 
pipe to prevent excessive back flow to pump.

Figure 14.

Condensate pump

Note:

Pour some water into the condensate drain(s) prior 
to start-up. This fills the trap and prevents air from 
being drawn up the drain lines.

Humidifier (Optional)

CeilAir systems may include an optional electrode steam 
humidifier. The humidifier empties into the condensate 
drain pan during the flush/drain cycle. A water supply line 
must be connected to the humidfier copper tubing inlet 
connection supplied by the factory. Refer to the installation 
drawing provided with your unit for the size and location 
of the connection. The humidifier requires normal tap 
water as the water supply. If the supply water is high in 
particulates, an external filter may be needed.

NOTICE

Humidifier Damage

Do not use demineralized water in the humidifier.

Note:

Refer to the humidifier operator's manual supplied 
with the TR-OHS unit for complete manufacturer's 
information on the humidifier and for supply water 
recommendations.

Utility Connections

Main Power

CeilAir units are available in single- or three-phase 
variations and a wide range of voltages. Examine the unit 
nameplate, located on the outside of the cabinet in close 
proximity of the electric box, to determine the operating 
voltage, frequency and phase of the system (see 

Figure 15, 

p. 21

). (Note that the unit serial and model numbers are

also found on the nameplate.) Provided power must meet 
the listed specifications. The supply voltage measured at
the unit must be within ±10% of the voltage specified on
the system nameplate, with the exceptions noted below.

The nameplate also provides the full load amps (FLA) the 
unit will draw under full design load, the minimum circuit 
ampacity (MCA) for wire sizing, and the maximum fuse 
size (MAX FUSE) for circuit protection.

Important:

If the nameplate states MAX FUSE/CKT 
BKR, fuses or an HACR type circuit breaker 
are required to protect the system. Other 
protection devices are not allowed based 
upon the product listing.

The unit is provided with terminals for all required field- 
wiring. It is important to identify the options that were 
purchased with the unit in order to confirm which field 
connections are required. Refer to the electrical drawing(s) 
supplied with the unit for information about power and 
control field-wiring.

Содержание CeilAir CW





















































Отзывы:

Нет отзывов