Trane Axiom GWS Series, Инструкция по установке, эксплуатации и обслуживанию

Страница: 67 / 76

WSHP-SVX015C-EN 67
N No otte e:: Do not release refrigerant to the atmosphere! If
adding or removing refrigerant is required, the
service technician must comply with all federal,
state and local laws.
Heating Season
• Inspect the unit’s air filters. If necessary, clean or
replace them.
• Check supply fan motor bearings; repair or replace
the motor as necessary.
• Inspect both the main unit control panel and heat
section control box for loose electrical components
and terminal connections, as well as damaged wire
insulation. Make any necessary repairs.
• Verify that the electric heat system operates
properly.
Coil Cleaning
Regular coil maintenance, including annual cleaning
enhances the unit’s operating efficiency by minimizing
the following:
• Compressor head pressure and amperage draw
• Water carryover
• Fan brake horsepower
• Static pressure losses
At least once each year—or more often if the unit is
located in a “dirty” environment—clean the evaporator
coils using the instructions outlined below. Be sure to
follow these instructions as closely as possible to avoid
damaging the coils.
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss C Ch he em miicca allss!!
C Co oiill cclle ea an niin ng g a ag ge en nttss cca an n b be e e eiitth he err a acciid diicc o orr h hiig gh hlly y
a allkka alliin ne e a an nd d cca an n b bu urrn n sse ev ve erre elly y iiff cco on ntta acctt w wiitth h sskkiin n
o orr e ey ye ess o occccu urrss..
H Ha an nd dlle e cch he em miicca all cca arre effu ulllly y a an nd d a av vo oiid d cco on ntta acctt w wiitth h
sskkiin n.. A AL LW WA AY YS S w we ea arr P Pe errsso on na all P Prro otte eccttiiv ve e
E Eq qu uiip pm me en ntt ((P PP PE E)) iin nccllu ud diin ng g g go og gg glle ess o orr ffa acce e ssh hiie elld d,,
cch he em miicca all rre essiisstta an ntt g gllo ov ve ess,, b bo oo ottss,, a ap prro on n o orr ssu uiitt a ass
rre eq qu uiirre ed d.. F Fo orr p pe errsso on na all ssa affe etty y rre effe err tto o tth he e cclle ea an niin ng g
a ag ge en ntt m ma an nu uffa accttu urre err’’ss M Ma atte erriia allss S Sa affe etty y D Da atta a S Sh he ee ett
a an nd d ffo ollllo ow w a allll rre ecco om mm me en nd de ed d ssa affe e h ha an nd dlliin ng g
p prra accttiicce ess..
Refrigerant Coils
To clean refrigerant coils, use a soft brush and a
sprayer.
For evaporator coil cleaners, contact the local Trane
Parts Center for appropriate detergents.
1. Remove enough panels from the unit to gain safe
access to coils.
2. Straighten any bent coil fins with a fin comb.
3. For accessible areas, remove loose dirt and debris
from both sides of the coil.
4. When cleaning evaporator coils, mix the detergent
with water according to the manufacturer’s
instructions. If desired, heat the solution to 150° F
maximum to improve its cleansing capability.
IIm mp po orrtta an ntt:: DO NOT use any detergents with
microchannel coils. Pressurized water
or air ONLY.
5. Pour the cleaning solution into the sprayer. If a
high-pressure sprayer is used:
a. The minimum nozzle spray angle is 15 degrees.
b. Do not allow sprayer pressure to exceed 600 psi.
c. Spray the solution perpendicular (at 90 degrees)
to the coil face.
d. For evaporator coils, maintain a minimum
clearance of 6" between the sprayer nozzle and
the coil. For microchannel coils, optimum
clearance between the sprayer nozzle and the
microchannel coil is 1"-3”.
6. Spray the leaving-airflow side of the coil first; then
spray the opposite side of the coil. For
evaporatorcoils, allow the cleaning solution to
stand on the coil for five minutes.
7. Rinse both sides of the coil with cool, clean water.
8. Inspect both sides of the coil; if it still appears to be
dirty, repeat Steps 6 and 7.
9. Reinstall all of the components and panels removed
in Step 1; then restore power to the unit.
10. For evaporator coils, use a fin comb to straighten
any coil fins which were inadvertently bent during
the cleaning process.
M Ma aiin ntte en na an ncce e