background image

Installation Checklist

 

Check the following points before testing the unit:

NO. 

Item to be checked

Possible problem

1

Have the indoor and outdoor units been 

securely installed?

The units may fall, vibrate or make noise. 

2

Has the refrigerant leak test been 

completed? 

Unresolved leaks may cause insufficient 

cooling or heating. 

3

Have the pipes been properly insulated? 

Lack of insulation may cause condensation 

and water damage. 

4

Is the water condensate drainage 

sufficient?

Lack of proper drainage may cause 

condensation and water damage.

5

Does the voltage of the power supply 

comply with the voltage on the nameplate?

Improper wiring can create malfunction and 

fire or electrocution hazard. 

6

Is the electric wiring and drain piping 

installed correctly? 

Improper wiring and drainage can create 

a malfunction, fire or electrocution hazard 

and water damage to the unit and property.

7

Is the unit grounded properly?

Improper grounding can cause malfunction 

and fire or electrocution hazard. 

8

Does the power cord match the unit 

requirements?

Improper wiring can create malfunction and 

fire or electrocution hazard. 

9

Are there any obstructions near the air 

inlets and air outlets for the indoor and 

outdoor units?

Improper ventilation and airflow will cause 

insufficient cooling and heating. 

10

Have dust and debris been cleaned and 

removed from the installation site? 

Excessive dust and debris in and around 

the units may cause a malfunction or 

damage to the units.

11

Are the gas valve and liquid valve of the 

connection pipes open completely?

Restricted refrigerant flow may cause 

insufficient cooling or heating. 

Test Operation:

1.  Turn on main power to the units. 

2.  Using the remote control, press the ON/OFF button to start operation. 

3.  Press the MODE button to select and test each option for normal operation. Cycle through all 

functions:  AUTO, COOL, DRY, FAN and HEAT.  

4.  Note: If the ambient temperature is lower than 61°F (16°C) the air conditioner will not run in 

COOL mode. 

5.  Go over basic operating, maintenance and troubleshooting functions with the customer. 

24

Ceiling Concealed Unit

Содержание American Standard 4MXD8509A





























Отзывы: