manualshive.com logo in svg

Trafox SUPERINTEND IM-04DCCT, Инструкция по установке и эксплуатации

Поделиться
Скачать
Trafox SUPERINTEND IM-04DCCT Скачать руководство пользователя страница 12

12

 

© Copyright Muuntosähkö Oy 

–

 Trafox

 

Superintend IMD 

 

http://www.trafox.fi

 

 

 

ALARM MENU 

 

The alarm menu has two levels.  The menu level shows if the alarm is active (ALARM), 
inactive but not acknowledged (OLD ALRM) or if the situation is normal (OK).  The 
screen mode shows the value, alarm limit and time of the parameter that caused the 
alarm. 

If the start-up delay has been enabled (SETUP

→

StDelay), the alarms cannot be 

activated before the set start-up delay has been elapsed after powering on the unit. 

An alarm always indicates that the fault in question is still active. An active fault cannot 
be acknowledged until the issue that caused it has been fixed.  The fixed fault is 
acknowledged when its time is checked and the T button is pressed. The   button takes 
you back to the menu level without acknowledging the fault. 

All fixed faults can also be acknowledged on one go by means of the Alarm reset function 
in the Monitor menu. 

If the automatic alarm acknowledgement has been enabled (SETUP

→

AutoRst), the faults 

are acknowledged automatically as soon as they are fixed. 

Содержание SUPERINTEND IM-04DCCT





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды