manualshive.com logo in svg

Trafox SUPERINTEND IM-04DCCT, Инструкция по установке и эксплуатации

Поделиться
Скачать
Trafox SUPERINTEND IM-04DCCT Скачать руководство пользователя страница 11

Superintend IMD

 

© Copyright Muuntosähkö Oy - Trafox

 

 

11 

 

http://www.trafox.fi

 

 

MONITOR MENU 

 

The Monitor menu is the default menu of the IM-04DCCT unit during use. All modes of 
the menu always return to the topmost item on the Monitor menu after 20 minutes from 
the last press of a button. 

 

The following measured parameters are available in the Monitor menu screen:  

•

 

IT network’s insulation resistance and capacitance in relation to protective earth. 

Displayed in kOhms and micro farads. 

•

 

Time and date 

•

 

All fixed alarms can be acknowledged on one go. 

•

 

Firmware version 

The default display is insulation resistance and capacitance.  Other parameters and 
functions can be viewed by using the   button.   

The system test is started from the Monitor menu by pressing T and then selecting Y in 
the Start test menu and pressing T. This starts the test of the internal measurement 
circuit of the IM-04DCCT unit.  If the test is completed successfully, the screen displays 
momentarily the text Test OK; otherwise the text shown in Test FAILED, and an 
insulation fault alarm is given to indicate that the insulation resistance can no longer be 
measured. 

The Monitor menu functions as follows: 

Содержание SUPERINTEND IM-04DCCT





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды