background image

 

     

  2 

Standard Warranty   

TRADEair compressors are covered  by the following warranty relating to the manufacturing process and material 

defects  if  the  compressor  is  operated  under  conditions  considered  by  us  as  normal  operating  conditions  as  is 

detailed  in  this  manual.  Furthermore  the  warranty  is  subject  to  the  compressor  being  maintained  and  serviced 

according to the guidelines contained herein. 

 

 

Compressor unit:

 within 14 months after the ex-factory date of delivery, or within 12 months after sale to the user, 

the earlier shall prevail. 

For the products not manufactured by TRADEair, the warranty clause of the original manufacturer shall be directly 

applied in feasible conditions. Within the warranty period, TRADEair or its agent shall be informed in writing within 

30 days of the defects being found, and the details shall be attached for identification, including the ex-factory serial 

number, model, purchasing date and other relevant information. 

 

 

The single responsibility assumed by TRADEair in this warranty is to repair or replace the component or parts which 

are proven defective. TRADEair requires the return of defective components or parts for inspection. 

 

 

 

Components or parts replaced during the warranty period will carry an additional 3 month warranty in cases where 

their replacement takes place with less than 3 months remaining under the standard warranty.   

 

 

 

 

 

 

 

 

 

 

 

Содержание MCFRC227






















Отзывы: