TracVision M3-DX Скачать руководство пользователя страница 27

Страница: 27 / 65

TracVision M3 User’s Guide

Chapter 4 - Setup

You can choose up to four different satellites from the
following list:

NOTE:

If the satellite you wish to track is not listed above, you can

set up a special user-defined satellite (USER A or USER B). See

“Programming User-Defined Satellites” on page 67

for details.

Press CHANGE until the display shows the first

(primary) satellite you want to install.

NOTE:

The display might show additional satellites not listed above.

However, at this time, the TracVision M3 system supports only the
satellites specified above.

Press ACCEPT.

• ARABSAT

• ASTRA 1

• ASTRA 2N

• ASTRA 2S

• EUTEL W3A

• HISPASAT

• HOTBIRD

• HOTBIRD WB

• NILESAT

• OPTUS B1

• OPTUS C1

• PAS 9

• SIRIUS

• THOR

• TURKSAT 1C

SAT 1= HOTBIRD?

CHANGE ACCEPT

SAT 2= NONE?

CHANGE ACCEPT

Содержание M3-DX


































































Результаты поиска

Содержание M3-DX

Отзывы:

Похожие инструкции для M3-DX

Бренды по названию

Популярные бренды

TracVision M3-DX, Руководство пользователя

Результаты поиска

Содержание M3-DX

Отзывы:

Похожие инструкции для M3-DX

Бренды по названию

Популярные бренды