Tracker LX4 2020, Руководство по ремонту и обслуживанию

Страница: 29 / 156

Read all of SAFETY and this section before attempting any procedure. Pay particular attention to Notices, Cautions, Warnings and Dangers.
Repair and Service Manual
699326
%2'<
*(1(5$/
NOTICE: Hardware that is removed must always be
installed in its original position unless otherwise
specified. If torque values are not specified, refer to
the Torque Specifications table in the GENERAL
INFORMATION AND ROUTINE MAINTENANCE sec-
tion.
To decrease the risk of injury or
death from battery explosion, bat-
teries should always be removed
before any servicing that will generate sparks.
It is important to use a sharp drill bit when remov-
ing the rivets on the side of the vehicle. Use
extreme care when drilling out the rivets located in
the front of the body and the bottom side of the
body. Excessive pressure could result in the drill
bit being forced through the body panel and pene-
trating an internal component. It is recommended
that a protective piece of sheet metal be placed
between the battery and the rivet as extra protec-
tion. Use of a drill depth stop will also provide addi-
tional protection.
%RG\FRPSRQHQWVFDQEHUHSODFHGZLWKDPLQLPXPRI
VSHFLDOWRROV0RVWERG\FRPSRQHQWVDUHKHOGLQSRVLWLRQ
ZLWKVWDQGDUGUHPRYDEOHKDUGZDUHQXWVEROWVZDVKHUV
DQGVFUHZV6RPHFRPSRQHQWVDUHLQVWDOOHGZLWKSRS
ULYHWVWKDWUHTXLUHWKHULYHWKHDGEHUHPRYHGWRSXVKWKH
VKDQNRIWKHULYHWRXW7KHULYHWKHDGFDQEHUHPRYHGE\
GULOOLQJLQWRWKHKHDGZLWKDVKDUSGULOOELWWKDWLVVOLJKWO\
ODUJHUWKDQWKHVKDQNRIWKHULYHW)LJXUH'RQRWDOORZ
WKHGULOOELWWRSXVKWKURXJKDQGGDPDJHFRPSRQHQWV
EHKLQGWKHULYHW8VHDVKDUSGULOOELWWKDWQHHGVPLQLPXP
SUHVVXUHWRFRUUHFWO\FXWDQGSXWDSLHFHRISURWHFWLYH
VKHHWPHWDOEHWZHHQWKHSDQHODQGFRPSRQHQWVEHKLQG
WKHSDQHO
%2'<&20321(175(3/$&(0(17
7RUHSODFHWKHERG\FRPSRQHQWVUHPRYHWKHPRXQWLQJ
KDUGZDUHUHSODFHWKHFRPSRQHQWDQGVHFXUHZLWKKDUG
ZDUHLQWKHRULJLQDOSRVLWLRQ
7KHIROORZLQJLOOXVWUDWLRQVLQGLFDWHWKHDVVHPEO\PHWKRGV
IRUWKHGLIIHUHQWFRPSRQHQWV)LJXUH)LJXUH
)LJXUH
)LJXUH'ULOO2XW0HWDO5LYHW
)LJXUH'ULYH5LYHW5HPRYDO
)LJXUH5HPRYH5DWFKHW)DVWHQHU
Pop Rivet
Drill out rivet
head only
Push pin with
screwdriver
from rear side
Drive pin through
with punch from
front
OR
Ratchet
Fastener
Remove fastener
with pry bar