TP-Link TL-WR702N Скачать руководство пользователя страница 67

Страница: 67 / 186

TL-WR702N

150Mbps Wireless N Nano Router

- 55 -

•

Received (Packets) -

Traffic that counted in packets has been received out from the WAN

port.

System Up Time

The length of the time since the Router was last powered on or reset.

Click the

Refresh

button to get the latest status and settings of the Router.

5.3 Quick Setup

Please refer to

Section 3.2: "Quick Installation Guide."

5.4 Working Mode

The Router supports five operation mode types:

AP, Router, Repeater, Bridge

and

Client

Please select one your want. Click

Save

to save your choice, which is shown as Figure 5-3.

Figure 5-3 Wireless Working Mode Settings

AP -

The wireless access point mode.

Router -

The wireless Router Mode. In this mode, the device enables multi-user to share

Internet via DSL/Cable Modem. The only wired port works as WAN.

Repeater -

The wireless Repeater Mode. It could extend the range of wireless network.

Bridge -

The wireless Bridge Mode. It could communicate with another wireless network.

Client -

The Client Mode. The computer connected by Ethernet could get access to an AP by

Client mode.

Click

in the following screen and then the Router will reboot and to work on Router Mode.

Figure 5-4

Содержание TL-WR702N



























































































































































































Результаты поиска

Содержание TL-WR702N

Отзывы:

Похожие инструкции для TL-WR702N

Бренды по названию

Популярные бренды

TP-Link TL-WR702N, Руководство пользователя

Результаты поиска

Содержание TL-WR702N

Отзывы:

Похожие инструкции для TL-WR702N

Бренды по названию

Популярные бренды