manualshive.com logo in svg

TP-Link HC220, Руководство пользователя

Поделиться
Скачать
TP-Link HC220 Скачать руководство пользователя страница 107

103

UKCA declaration of conformity

TP-Link hereby declares that the device is in compliance with the essential requirements 
and other relevant provisions of the Radio Equipment Regulations 2017.
The original UK declaration of conformity may be found at https://www.tp-link.com/
support/ukca 

National restrictions

Attention: This device may only be used indoors in Great Britain.

Canadian Compliance Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with 
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). 
Operation is subject to the following two conditions:
(1 )  This device may not cause interference.
(2 )  This device must accept any interference, including interference that may cause 

undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme 
aux CNR d’Innovation, Sciences et Développement économique Canada applicables 
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions 
suivantes :
1 )  L’appareil ne doit pas produire de brouillage;
2 )  L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage 

est susceptible d’en compromettre le fonctionnement.

Caution:

The device for operation in the band 5150–5250 MHz is only for indoor use to reduce 
the potential for harmful interference to co-channel mobile satellite systems.

Avertissement:

Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour 
une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux 

Содержание HC220















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды