TP-Link Archer C3000 Скачать руководство пользователя страница 53

Страница: 53 / 83

To use the smart connect function

The smart connect function helps devices run faster by assigning them to best wireless bands based on actual conditions to

balance network demands.
1. Select the

Smart Connect

checkbox, and click

Save

2. Keep the default or set a new SSID and password, and c

lick

Save

This SSID and password will be applied for 2.4GHz, 5GHz-1, and 5GHz-2 wireless networks

To change the security option:

In the

Wireless

section, select an option from the

Security

dropdown list.

The router provides four security options, No Security, WPA/WPA2 - Personal (Recommended), WPA/WPA2 - Enterprise and

WEP. We recommend you don’t change the default settings unless necessary. If you select other options, configure the related

parameters according to the help page.

In addition

•

Mode

- Select a transmission mode according to your wireless client devices.

802.11b/g/n mixed

802.11g/n mixed

802.11n only

for

2.4GHz

; and

802.11a/n/ac mixed

802.11n/ac mixed

802.11ac only

for

5GHz

. It is recommended to just

leave it as default.

•

Channel Width

- Select a channel width (bandwidth) for the wireless network.

•

Channel

- Select an operating channel for the wireless network. It is recommended to leave the channel to

Auto

, if you are

not experiencing the intermittent wireless connection issue.

•

Transmit Power

- Select either

High

Middle

Low

to specify the data transmit power. The default and recommended

setting is

High

Содержание Archer C3000




















































































Результаты поиска

Содержание Archer C3000

Отзывы:

Похожие инструкции для Archer C3000

Бренды по названию

Популярные бренды

TP-Link Archer C3000, Руководство пользователя

Результаты поиска

Содержание Archer C3000

Отзывы:

Похожие инструкции для Archer C3000

Бренды по названию

Популярные бренды