Toyota PTS21-21070 Скачать руководство пользователя

Страница: 11 / 17

SCION tC

2008-

ILLUMINATED

DOOR

SILLS

Procedure

Page 11 of 17 pages

Issue: C 06/13/07

(d)

Route the Crossover harness toward the
center console area. (Fig. 4-4)

(1)

Route the Crossover harness through the
opening space in front of the driver side
brace as shown.

(2)

Install thick foam tape to brace to protect
the harness.

(e)

Secure the crossover harness to vehicle
harness with three wire ties in the driver side
center console area. (Fig. 4-5)

(f)

Route the crossover harness toward the glove
box area, then secure it to the vehicle harness
with three wire ties in the passenger side
center console area. (Fig. 4-6)

(g)

Route the Crossover harness to the glove box
area, then secure it to the vehicle harness
with five wire ties. (Fig. 4-7)

Fig.

4-7

Wire Ties

Wire Cutters

Fig.

4-4

Crossover

Harness

Brace

Foam

Pad

Wire Cutters

Fig.

4-6

Wire Cutters

Wire Ties

Harness

Fig.

4-5

Wire Ties

Wire Cutters

Содержание PTS21-21070


















Результаты поиска

Содержание PTS21-21070

Отзывы:

Похожие инструкции для PTS21-21070

Бренды по названию

Популярные бренды

Toyota PTS21-21070, Руководство пользователя

Результаты поиска

Содержание PTS21-21070

Отзывы:

Похожие инструкции для PTS21-21070

Бренды по названию

Популярные бренды