manualshive.com logo in svg

Toyota AVALON 2005, Руководство по эксплуатации


Поделиться
Скачать
background image

’05 MATRIX_U (L/O 0409)

219

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

Total trailer weight

Total trailer weight

Tongue load

Tongue load

 100 = 9 to 11%

The trailer cargo load should be
distributed so that the tongue load
is 9 to 11% of the total trailer
weight, not exceeding the maximum
of 68 kg (150 lb.). Never load the
trailer with more weight in the back
than in the front. About 60% of the
trailer load should be in the front
half of the trailer and the remaining
40% in the rear.

HITCHES

Use only a weight carrying hitch
designed for the total trailer weight.
Toyota does not recommend using a
weight distribution (load equalizing)
hitch.

The hitch must be bolted securely to
the vehicle frame and installed accord-
ing to the hitch manufacturer’s instruc-
tions.

The hitch ball should have a light coat
of grease.

Toyota recommends that the trailer
hitch be removed when not towing to
prevent injury and/or damage by the
hitch in event of a rear end collision.
After removing the hitch, the installa-
tion area should be sealed to prevent
entry of exhaust fumes and mud.

NOTICE

Do not use an axle- mounting hitch as
it may cause damage to the axle
housing, wheel bearings, wheels and/
or tires.

BRAKES AND SAFETY CHAINS

Toyota recommends trailers with
brakes that conform to any applica-
ble federal and state/provincial regu-
lations.

A safety chain must always be used
between the towing vehicle and the
trailer. Leave sufficient slack in the
chain for turns. The chain should
cross under the trailer tongue to
prevent the tongue from dropping to
the ground in case it becomes dam-
aged or separated. For correct safety
chain procedures, follow the hitch or
trailer manufacturer’s recommenda-
tions.

CAUTION

If the total trailer weight exceeds
453 kg (1000 lb.), trailer brakes are
required.

Never tap into your vehicle’s hy-
draulic system as it would lower its
braking effectiveness.

Содержание AVALON 2005
































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AVALON 2005

Lancia Delta Owner'S Handbook Manual preview
Delta
Бренд: Lancia Страницы: 276
T-Tech TT100 User Manual preview
TT100
Бренд: T-Tech Страницы: 38
Cequent 10417 Instruction Sheets preview
10417
Бренд: Cequent Страницы: 9
iDataLink BLADE-AL(TB)-TL2 Install Manual preview
BLADE-AL(TB)-TL2
Бренд: iDataLink Страницы: 9
Magneti Marelli BCF184 Installation Instructions preview
BCF184
Бренд: Magneti Marelli Страницы: 2
EEZ RV 51 SC Instruction Manual preview
51 SC
Бренд: EEZ RV Страницы: 31
Jeep PATRIOT 2013 Manual preview
PATRIOT 2013
Бренд: Jeep Страницы: 16
Audi RSE III Quick Start Manual preview
RSE III
Бренд: Audi Страницы: 4
Park-Daddy PD50AA Installation Manual preview
PD50AA
Бренд: Park-Daddy Страницы: 22
Skoda OCTAVIA - TECHNICAL CHANGES 11-2009 Owner'S Manual Supplement preview
OCTAVIA - TECHNICAL CHANGES 11-2009
Бренд: Skoda Страницы: 16
Ranger design 1506-PHX Cargo Plus Installation Manual preview
1506-PHX Cargo Plus
Бренд: Ranger design Страницы: 8
AUTOTECH 10.411.01.219K Installation Instructions preview
10.411.01.219K
Бренд: AUTOTECH Страницы: 1
Camoplast T4S Installation Manuallines preview
T4S
Бренд: Camoplast Страницы: 19
S3 Power Sports S3193 Installation Instructions preview
S3193
Бренд: S3 Power Sports Страницы: 2
Subaru 2004 Impreza OUTBACK SPORT Owner'S Manual preview
2004 Impreza OUTBACK SPORT
Бренд: Subaru Страницы: 34
Saab 32 025 603 Installation Instructions Manual preview
32 025 603
Бренд: Saab Страницы: 15
NavInc CP-PEU-GV3 Manual preview
CP-PEU-GV3
Бренд: NavInc Страницы: 6
E&G Classics Denali 1094-0185-15 Instruction Manual preview
Denali 1094-0185-15
Бренд: E&G Classics Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды