manualshive.com logo in svg

Toyota AVALON 2005, Руководство по эксплуатации


Поделиться
Скачать
background image

’05 MATRIX_U (L/O 0409)

29

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

SETTING THE SYSTEM

You can set the system as follows.

1. Remove the key from the ignition

switch.

The indicator light will start flashing when
the key is removed from the ignition
switch. (See “Engine immobilizer system”
on page 14 for details.)

2. Have all passengers get out of the

vehicle.

3. Close all the side doors, back door and

glass hatch securely.

4. Lock all the side doors and back door

with the key or wireless remote control
transmitter. At this time, the TVIP indi-
cator light comes on.

The system will be set in 30 seconds.
When the system is set, the indicator
light will start flashing again.

5. Make sure that the indicator light

flashes. Then you may leave the ve-
hicle.

Never leave anyone in the vehicle when
you set the system because unlocking
from the inside activates the alarm.

Activating the alarm

If the system detects a threat to the
vehicle, it sounds the alarm for one
minute while flashing headlights and
turn signal lights. Also,  the interior
lights turn on when the interior light
dial is in the door position.

The system detects a threat under any of
the following conditions:

Either of the front doors is unlocked by
means other than the key or wireless
remote control transmitter.

If the key is not in the ignition switch,
all the side doors and back door will
be automatically locked again.

Any of the side doors, back door or
glass hatch are forcibly opened.

The alarm will activate when the back
door is unlocked with a key. Cancel the
system before unlocking the back door.

The side windows are tapped or bro-
ken.

The battery terminal is disconnected
and then reconnected.

The ignition is hotwired.

After one minute, the alarm automatically
stops and the indicator light starts flashing
again.

Reactivating the alarm

Once set, until you cancel the system, the
system automatically resets the alarm af-
ter the alarm has stopped.

The alarm will activate again under the
same circumstances described in “Activat-
ing the alarm”.

Stopping the alarm

You  can stop the alarm in either of the
following ways:

Unlock any of the side doors and back
door with the key or wireless remote
control transmitter.

Place the ignition switch in the “ON”
position.

Содержание AVALON 2005
































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AVALON 2005

Quadratec QR3 Installation Manual preview
QR3
Бренд: Quadratec Страницы: 8
DAVIS 8126GD User Manual preview
8126GD
Бренд: DAVIS Страницы: 32
Edelbrock For 1985-1992 GM Cars and Trucks 17933 Installation Instructions preview
For 1985-1992 GM Cars and Trucks 17933
Бренд: Edelbrock Страницы: 4
B-Speech Pago INBTHF020 User Manual preview
Pago INBTHF020
Бренд: B-Speech Страницы: 24
RBP STEALTH POWER RBP-216-SP Installation Manual preview
STEALTH POWER RBP-216-SP
Бренд: RBP Страницы: 16
HURST STREET SUPER SHIFTER Installation Instructions preview
STREET SUPER SHIFTER
Бренд: HURST Страницы: 2
FALCON RIDGE HO-P500-FC04 Instructions For Installation And Care preview
HO-P500-FC04
Бренд: FALCON RIDGE Страницы: 8
Scosche 142HUD2 Manual preview
142HUD2
Бренд: Scosche Страницы: 8
Whispbar K607W Fitting Instructions Manual preview
K607W
Бренд: Whispbar Страницы: 14
Ford 2005 P207 Explorer Sport Trac Owner'S Manual preview
2005 P207 Explorer Sport Trac
Бренд: Ford Страницы: 540
ACV 281178-28G-M Installation Manual preview
281178-28G-M
Бренд: ACV Страницы: 2
JBL smartbase Quick Start Manual preview
smartbase
Бренд: JBL Страницы: 12
Wagan Easy Air Auto Screen User Manual preview
Easy Air Auto Screen
Бренд: Wagan Страницы: 8
Mont Blanc ACTIVA+ Assembly Instructions preview
ACTIVA+
Бренд: Mont Blanc Страницы: 2
Cadillac 2005 XLR Owner'S Manual preview
2005 XLR
Бренд: Cadillac Страницы: 438
Edelbrock 67312 Installation Instructions preview
67312
Бренд: Edelbrock Страницы: 2
Arctic Cat 2010 ATV 150 Service Manual preview
2010 ATV 150
Бренд: Arctic Cat Страницы: 101
Kuda 193400 Installation Instruction preview
193400
Бренд: Kuda Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды