manualshive.com logo in svg

Toyota AVALON 2005, Руководство по эксплуатации


Поделиться
Скачать
background image

’05 MATRIX_U (L/O 0409)

134

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

If the vehicle speed drops 16 km/h (10
mph) below the preset speed, the preset
speed will also automatically cancel out.

If the preset speed automatically cancels
out other than for the above cases, have
your vehicle checked by your Toyota deal-
er at the earliest opportunity.

RESETTING TO A FASTER SPEED

Push the lever up in the “+ RES” direction
and hold it. Release the lever when the
desired speed is attained. While the lever
is held up, the vehicle will gradually gain
speed.

However, a faster way to reset is to ac-
celerate the vehicle and then push the
lever down in the “-  SET” direction.

RESETTING TO A SLOWER SPEED

Push the lever down in the “-  SET” direc-
tion and hold it. Release the lever when
the desired speed is attained. While the
lever is held down, the vehicle speed will
gradually decrease.

However, a faster way to reset is to de-
press the brake pedal and then push the
lever down in the “-  SET” direction.

On vehicles with automatic transmission,
even if you turn off the overdrive switch
with the cruise control on, engine braking
will not be applied because the cruise
control is not cancelled. To decrease the
vehicle speed, reset to a slower speed
with the cruise control lever or depress
the brake pedal. If you use the brake
pedal, cruise control is cancelled.

RESUMING THE PRESET SPEED

If the preset speed is cancelled by pulling
the control lever or by depressing the
brake pedal or clutch pedal, pushing the
lever up in the “+ RES” direction will re-
store the speed set prior to cancellation.

Except for two- wheel drive models with
1ZZ- FE engine—However, once the ve-
hicle speed falls below about 40 km/h (25
mph), the preset speed will not be re-
sumed.

CRUISE CONTROL FAILURE WARNING

If the “CRUISE” indicator light in the
instrument cluster flashes when using the
cruise control, press the “ON- OFF” switch
to turn the system off and then press it
again to turn it on.

If any of the following conditions then oc-
curs, there is some trouble in the cruise
control system.

The indicator light does not come on.

The indicator light flashes again.

The indicator light goes out after it
comes on.

If this is the case, contact your Toyota
dealer and have your vehicle inspected.

Содержание AVALON 2005
































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AVALON 2005

AC Schnitzer F40 Fitting Instructions Manual preview
F40
Бренд: AC Schnitzer Страницы: 16
Whispbar K783W Fitting Instructions Manual preview
K783W
Бренд: Whispbar Страницы: 16
TATA Motors nano genX Owner'S Manual preview
nano genX
Бренд: TATA Motors Страницы: 156
Whispbar K934W Fitting Instructions Manual preview
K934W
Бренд: Whispbar Страницы: 15
Hama 00178266 Operating Instruction preview
00178266
Бренд: Hama Страницы: 75
Wagan Road Ready Seat Protector User Manual preview
Road Ready Seat Protector
Бренд: Wagan Страницы: 12
Chevrolet 2016 Suburban Owner'S Manual preview
2016 Suburban
Бренд: Chevrolet Страницы: 50
BrandMotion FLTW-7690 Installation Instructions preview
FLTW-7690
Бренд: BrandMotion Страницы: 2
Quadratec 12057.0263 Installation Manual preview
12057.0263
Бренд: Quadratec Страницы: 12
T-Mobile SyncUP DRIVE Start Manual preview
SyncUP DRIVE
Бренд: T-Mobile Страницы: 2
NavInc CP-PEU-GV3 Manual preview
CP-PEU-GV3
Бренд: NavInc Страницы: 6
E&G Classics Denali 1094-0185-15 Instruction Manual preview
Denali 1094-0185-15
Бренд: E&G Classics Страницы: 3
Metra Electronics 99-7803G Wiring Instructions preview
99-7803G
Бренд: Metra Electronics Страницы: 2
Oldsmobile 1995 Cutlass Supreme Owner'S Manual preview
1995 Cutlass Supreme
Бренд: Oldsmobile Страницы: 340
Joie i-Level Instruction Manual preview
i-Level
Бренд: Joie Страницы: 53
ORA XL MIRROR Installation Instructions Manual preview
XL MIRROR
Бренд: ORA Страницы: 7
Skoda FABIA II TMB PS 035 Mounting And User Instructions preview
FABIA II TMB PS 035
Бренд: Skoda Страницы: 16
Westin 32-2250 Instructions preview
32-2250
Бренд: Westin Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды