background image

Stop
here

Fuel Gauge

Manual shutoff button

Igniter button

Wick adjuster knob

Removable fuel tank

Top plate

Grille

Body

Heat
chamber

Tank lid

Drip tray

Fuel indicator

Front panel

1. Open the fuel tank lid on the top of heater cabinet and lift out the 

removable fuel tank. Turn the removable tank upside down and 
remove the fuel tank cap.

2. Insert the straight tube of the manual siphon into the kerosene 

container. Insert the siphon’s flexible hose into the removable 
fuel tank opening.

 3. Turn the air vent knob on the top of the siphon clockwise to close 

the vent. Start the flow of kerosene by squeezing the bulb of the 
siphon vigorously six or seven times. Once flow begins, it is no 
longer necessary to squeeze the bulb.

4. Watch the fuel gauge on the removable tank to avoid overfilling. 

When it shows half, stop flow by turning the air vent knob 
counterclockwise.

NOTE:

Be careful to avoid overfilling the tank, especially with 

very cold kerosene. Overflow might occur due to 
expansion when the fuel warms up.

5. Remove the siphon carefully, allowing excess  kerosene to drain from the tube back into the 

container. replace fuel tank cap and tighten it securely. Be sure to wipe away any spilled 
kerosene from tank and other heater parts.

6. After making sure fuel tank cap is tightly fastened, invert tank and replace into heater body.

2

 Model RCA-2800 (E)  06.12.12 9:08 AM  ページ 2

Содержание RCA-2800













Отзывы: