background image

YW1838 

 

Definitions

 

 

 

Code Length:

 Length of Master Code defines the length of all other codes. Length of codes can be 4, 5 or 6 digits. Master 

Code and User Codes must be the same length. 

 

LED Indicator:

 LED indicators are located at the top outside of the lock. Lock flashes green LED and/or red LED 

dependent on inputs. 

 

Master Code:

 Code used to program the lock and unlock the lock. Factory Default Settings Master Code is 12345 - this 

must be changed before programming the lock. Each lock has only one Master Code. Multiple locks can have same Master 
Code.  

 

User ID:

 Two-digit identification numbers for User Codes. Each User Code must have a User ID (00-99).  

 

User Code:

 Codes used to unlock the lock. User Codes are programmed by Master Code. Lock can have a maximum of 

100 User Codes. Program 02 programs User IDs and their User Codes. 

 

Service Code (One-time User Code):

 Code that allows one entry per code. Service Code is deleted after it has been 

used. Lock can have a maximum of 5 Service Codes active simultaneously.  

 

Passage Mode:

 Mode that keeps the lock unlocked until it is disabled. Factory Default Settings has this mode disabled. 

Program 40 enables Passage Mode and Program 41 disables Passage Mode. 

 

Pass Time:

 Period that a lock stays in unlocked position after a valid code is entered. Factory Default Settings Pass Time 

is 5 seconds. Program 42 adjusts Pass Time from 2 to 20 seconds. Stays in unlocked position. Turning inside or outside 
lever opens the lock.  

 

Sound:

 Keypad sound is enabled by Factory Default Settings. Disabling the sound does not affect general operation and 

programming of the lock. Program 73 disables sound and Program 71 enables Sound.  

 

Lock Status Indicator:

 LED indicator on lock to show whether it is locked (flashing red LED) or unlocked (flashing green 

LED). Program 91 enables or disables the lock status indicator.  

 

Penalty Time (Keypad Anti-Tamper Lockout Time):

 Period that a lock stays in locked position after it reached its max 

number of incorrect code entries. During Penalty Time, no other codes will be accepted. Factory Default Settings Penalty 
Time is 60 seconds after 3 invalid tries. Program 92 adjusts Penalty Time from 0 (disabled) to 90 seconds after 0 (disabled) 
to 9 tries. This is used to prevent unauthorized entry.  

 
 

Содержание e-Smart 2000 Series













Отзывы: