Town & Country Fireplaces TCWS.54NG04.C Скачать руководство пользователя страница 5

Страница: 5 / 12

10. Place the front pebble cluster over the

burner. Use the pins on the burner

and holes in the pebble cluster to

locate the pebbles on the burner.

(Fig.

#10)

11. Place the top rocks on top of the

pebble clusters as shown. Use the

slots in the top rock to align to the tabs

on the pebble clusters.

(Fig. #11a & 11b)

12. Repeat the sequence of placing the

front, rear and top rocks three more

times until the burner is covered.

13. Place equalizer rocks at either end of

burner as shown. (Fig. #12)

14. Install front porcelain cover

(wide edge should face the front).

(Fig. #13 & #13A)

Fig #10

Fig #11a

Fig #12

Fig #13

Fig #13A

Fig #11b

WIDE SECTION
TO FRONT

FRONT CLUSTER

SLOPE INTO
THE CLUSTER

REAR
CLUSTER

THIS EDGE

TO FRONT OF FIREPLACE

TCWS.54NG04.C 040907

Содержание TCWS.54NG04.C













Результаты поиска

Содержание TCWS.54NG04.C

Отзывы:

Похожие инструкции для TCWS.54NG04.C

Бренды по названию

Популярные бренды

Town & Country Fireplaces TCWS.54NG04.C, Инструкция по эксплуатации

Результаты поиска

Содержание TCWS.54NG04.C

Отзывы:

Похожие инструкции для TCWS.54NG04.C

Бренды по названию

Популярные бренды