background image

WARNING

This conversion kit 
shall be installed by a 
qualifi ed service agency 
in accordance with the 
manufacturer's instructions 
and all applicable codes and 
requirements of the authority 
having jurisdiction. 

If the information in these 
instructions is not followed 
exactly, a fi re, explosion 
or production of carbon 
monoxide may result 
causing property damage, 
personal injury or loss of 
life. 

The qualifi ed service agency 
is responsible for the proper 
installation of this kit. The 
installation is not proper and 
complete until the operation 
of the converted appliance is 
checked as specifi ed in the 
manufacturer's instructions 
supplied with the kit

.

If the unit is to be used on propane, 
convert as follows using the 
components supplied with this 
fi replace:

CAUTION

The gas supply and electrical power 
must be shut off before proceeding 
with the conversion.

Note: 
Factory supplied components must be used 
to ensure correct input.  After conversion 
confi rm proper manifold pressure.

1.  Ensure the burner, pilot and gas 
 

supply are turned off, and the 

 

appliance has cooled.

2.  Using a 1/2” wrench, undo both natural 

gas burner orifi ces (marked 

#29

).

 (Fig. 

#18)

3.  Apply a small amount of pipe joint com-

pound to the threads of the propane 
burner orifi ce (marked #

44

) to ensure 

a good seal, before screwing it into the 
fi tting.

4.  Open primary air shutters fully.

5.    With a 7/16” wrench loosen the pilot head 

on the pilot assembly (Fig. #19)

6.    Slide the pilot adjustment band over and 

ensure that the hole in the orifi ce band is 
showing. (Fig. #20 indicates NG position, 
Fig. #21 indicates LP position)

 

Repeat steps 5 and 6 for other pilot.

TC54.NGO3C2 070211-16

Fig #18

Fig #19

Fig #20

Fig #21

LP GAS/ 

DU GAZ LP 

12.5 in/wc /12.5 po/c.e. 
     (3.11 kPa) 

      

13.9 in/wc / 13.9 po/c.e. 
     (3.45 kPa) 

      

11.0 in/wc / 11.0 po/c.e. 
     (.95 kPa) 

      

#44     (2.18 mm) 

Max.:   83,700   (24.53)
Min.:    67,000   (19.63)

230910      6-TC54C2    5052.520862

Date: ______________________

By / Par:  ___________________  

Kit# TC54.LPCE02 for use with model / 
Pour utilise avec du modèle:

 TC54.CE2

This appliance was con-
verted to PROPANE GAS 
with this kit on this date 
by the organization which 
accepts the responsibility 
that this conversion has 
been properly made. / Cet 
appariel etair converter au 
gaz LP par l’emploi de la 
trousse de conversion par 
une organization qui ac-
cepte la responsibilité pour 
une installation en bon état.

MAIN BURNER 
(#44) ORIFICES  (5022.92)

MINIMUM RATE SCREW (5005.015)

CONVERSION LABEL (5052.52086)

8

Propane Conversion

Содержание TC54.NG03C2

















Отзывы: