Town & Country Fireplaces TC36STD2 Скачать руководство пользователя

Страница: 34 / 40

TC36STD2

FOR YOUR SAFETY READ BEFORE LIGHTING

LIGHTING INSTRUCTIONS

TO TURN OFF GAS APPLIANCE

WARNING:

If you do not follow these instructions exactly, a

fire or explosion may result causing property damage,

personal injury or loss of life.

A. This appliance is equipped with an ignition device which

automatically lights the pilot. Do not try to light the pilot by hand.

B. BEFORE LIGHTING smell all around the appliance area for gas. Be

sure to smell next to the floor because some gas is heavier than

air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS:

- Do not try to light any appliance.

- Do not touch any electric switch; do not use any phone in your

building.

- Immediately call your gas supplier from a neighbour's phone. Follow

the gas supplier's instructions.

- If you cannot reach your gas supplier, call the fire department.

C. Use only your hand to push in or turn the gas control knob. Never use

tools. If the knob will not push in or turn by hand, don't try to repair it,

call a qualified service technician. Force or attempted repair may

result in a fire or explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect the

appliance & to replace any part of the control system & any gas

control which has been under water.

1. STOP! Read the safety information above on this label.

2. This appliance is equipped with an ignition device which

automatically lights the pilot. Do not try to light the pilot by hand.

3. Push the "On/ Off" switch to turn the fireplace ON.

- If the burner does light go to step 6.

- If the burner does not light, complete steps 4 through 5.

- If the burner will not light or stay lit after several tries, push the

"On/ Off" switch for the fireplace to OFF, turn off all electric power

to the fireplace and call your service technician or gas supplier.

Note: Sufficient time must be allowed for air to escape from lines if

the unit is being lit for the first time.

4. Push the "On/ Off" switch to the fireplace Off.

5. Allow sufficient length of time (minimum 5 minutes) for any gas in the

combustion chamber to escape. If you still smell gas, STOP! Follow

"B" in the safety information above on this label. If you don't smell

gas, go to step 3.

6. Set fireplace to desired setting by using hand held remote.

Push the "on/ off" switch to the "Off" position.

2. Turn off all electric power to the appliance and remove backup

batteries if service is to be performed or for extended shutdown.

Due to high surface temperatures, keep children, clothing and furniture away. Keep burner and control compartment clean. See installation and

operating instructions accompanying the appliance.

A cause de la temperature elevee des parios, tenir eloignes les enfants, les vetements et les meubles. Maintenir propres le bruleur et le

compartiment de commande. Voir les instructions relatives a l'installation et au fonctionnement qui accompagnent l'appareil.

CAUTION

Hot while in operation. Do not touch. Severe burns may result. Keep children,

clothing, furniture, gasoline and other liquids having flammable vapours away. Keep burner and control

compartment clean. See installation and operating instructions accompanying the appliance.

ATTENTION

L'appareil est chaud lorsqu'il fonctionne. Ne pas toucher l'appareil. Risque de

brûlures graves. Serveiller les enfants. Garder les vêtements, le meubles, l'essence ou autres liquides

produisant des vapeurs infl ammables loin de l'appareil. S'assurer que le brûleur et le compartiment des

commandes sont propres. Voir les instructions d'installation et d'utilisation qui accompagnent l'appareil.

090713

5051.185

GBWY

100000438-50 091418-41

Lighting Instructions

Содержание TC36STD2









































Результаты поиска

Содержание TC36STD2

Отзывы:

Похожие инструкции для TC36STD2

Бренды по названию

Популярные бренды

Town & Country Fireplaces TC36STD2, Руководство по установке

Результаты поиска

Содержание TC36STD2

Отзывы:

Похожие инструкции для TC36STD2

Бренды по названию

Популярные бренды