background image

9

TC30.NG04C 180411-20

WARNING

This conversion kit 
shall be installed by a 
qualifi ed service agency 
in accordance with the 
manufacturer's instructions 
and all applicable codes 
and requirements of 
the authority having 
jurisdiction. 

If the information in these 
instructions is not followed 
exactly, a fi re, explosion 
or production of carbon 
monoxide may result 
causing property damage, 
personal injury or loss of 
life. 

The qualifi ed service 
agency is responsible for 
the proper installation of 
this kit. 

The installation is not 
proper and complete 
until the operation of the 
converted appliance is 
checked as specifi ed in the 
manufacturer's instructions 
supplied with the kit.

If the unit is to be used on  propane 
 conver t as follows using the 
 components supplied with this 
burner:

CAUTION

The gas supply and electrical power 
shall be shut off before proceeding 
with the conversion.

Note: 
Factory supplied components must be used 

to ensure correct input.  

After conversion confi rm proper manifold 

pressure.

1. 

Remove the 2 front screws holding the  

 

burner tray in place. 

 (Fig. 

#16)

2. 

Gently lift up the burner tray while  

 

sliding to the left to disengage the  

 

burner tube from the orifi ce. Then tip  

 

back to expose the orifi ce.

3. 

Using a 1/2” wrench, undo the 

 

natu ral gas burner orifi ce, 

 (marked 

#32

). Apply a small amount  

 

of pipe joint compound to the threads  

 

of the propane burner orifi ce 

 (marked 

#48

) to ensure a good seal,  

 

before screwing it into the fi tting. 

 

Loosen the primary air shutter screw,  

 open 

shutter 

half way

 and re-tighten. 

 (Fig. 

#17)

4.  

Remove the 2 screws holding the 
pilot assembly in place with a stubby 
screwdriver. 

 (Fig 

#18)

 

The burner assembly must 
be removed from the unit if 
previously installed.

Fig #16

Fig #17

Fig #18

Propane Conversion

 For use with model:
 Pour utilise avec du modèle:

LP GAS/ 

DU GAZ LP 

12.5 in/wc /12.5 po/c.e. 
     (3.11 kPa) 

      

13.9 in/wc / 13.9 po/c.e. 
     (3.45 kPa) 

      

11.0 in/wc / 11.0 po/c.e. 
     (.95 kPa) 

      

# 48     (1.93 mm) 

Max.:   35,000   (10.3)
Min.:    27,000  (7.91)

 

080411 6-TC30 5052.52085

Date:

 ______________________

By / Par:

 ___________________  

This appliance was converted 
to PROPANE GAS with this kit 
on this date by the organiza-
tion which accepts the respon-
sibility that this conversion 
has been properly made. / Cet 
appariel etair converter au gaz 
LP par l’emploi de la trousse 
de conversion par une organi-
zation qui accepte la responsi-
bilité pour une installation en 
bon état.

 

TC30

Series C

MAIN BURNER 
(#48) ORIFICE (5021.3407)

MINIMUM RATE SCREW (5005.011)

Содержание TC30.NG04C





















Отзывы: