background image

 NST13308-M115-02_A     

◄►

     2021-06-23     

◄►

     Page 14

Indiana Local

1-574-294-2570

Toll Free

1-800-294-2570

Fax

1-574-293-1611

Phone

1-800-294-2570

Fax

1-574-293-1611

Email

[email protected]

TECHNICAL SUPPORT NUMBERS

SALES SUPPORT NUMBERS

TECHNICAL SUPPORT VIA WEBSITE / EMAIL

www.touchtronics.com
[email protected] or 'Contact Request' link on 

the web page

PARTS

1. Each individual product is warranted under the TouchTronics Limited Warranty program for one (1)   

  full year from the date of purchase or two (2) years from the date of manufacture.

2. No product will be covered under the TouchTronics Limited Warranty program that has a  

 

 

  maunufacture date older than two (2) years.

3. To receive technical support or warranty service, call our technical support center at 1-800-294-2570  

  during regular business hours.

4. To enable our technical staff to better serve you, please have the product and vehicle information    

  available when you call.

TOUCHTRONICS, INC. WARRANTY POLICES AND PROCEDURES

Model Number
Serial Number
Date of Purchase
Date of Installation

Dealer Name
Dealer Phone
Make / Model

VEHICLE INFORMATION

PRODUCT INFORMATION

     * Fill in all pertinent information at the time of purchase or installation.

© 2021 TouchTronics, Inc. All Rights Reserved.TouchTronics, the TouchTronics logo, and other TouchTronics marks are owned by TouchTronics and may 

be registered. TouchTronics assumes no responsibility for any errors that may appear in this manual. Information contained herein is subject to change 

without notice.
FCC Compliance and Advisory Statement - This hardware device complies with Part 15 of the FCC Rules. Operation is subject to the following two 

conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Canadian Compliance Satement - This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic 

Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause undesired operation of the device.
*********************************************************************************************************************************************

© 2021 TouchTronics, Inc. Tous droits réservés.TouchTronics, le logo TouchTronics et les autres marques TouchTronics sont la propriété exclusive de 

TouchTronics et sont susceptibles dêtre des marques déposées. Toutes les autres marques sont la propriété exclusive de leurs détenteurs respectifs. 

TouchTronics décline toute responsabilité en cas derreurs dans ce manuel.  Les informations énoncées dans le présent document peuvent faire lobjet de 

modifications sans avis préalable.
Déclaration FCC - Cet équipement a été testé et déclaré conforme à la section 15 du règlement de la FCC. Son fonctionnement est soumis aux 

conditions suivantes:

1. Léquipement concerné ne doit pas causer dinterférences dangereuses.

2. Il doit accepter toute interférence reçue, y compris les interférences risquant dengendrer   unfonctionnement indésirable

Toutes modifications ou tous changements effectués sans laccord exprès de la partie responsable de la conformité aux normes pourraient contraindre 

lutilisateur à ne plus utiliser son équipement.
Déclaration du Ministère des Communications Canadien - L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR 

d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux 

conditions suivantes:

1. L’appareil ne doit pas produire de brouillage.

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

FCC & ISED COMPLIANCE

Содержание Invisilok - M115

















Отзывы: