background image

INSTALLATION & INSTRUCTION MANUAL FOR BATH & SHOWER SET

DGM301CFN/ DGM301CFNS

Quantity

Part name

Shower faucet

Shower head

1 set

1 pc

Part name

Hanger

Hose

150±20

150

Wall line

22.5

Hot

Cold

Length

1500

Open

Red

Blue

Close

2-Ø6x30

Connector

● Always wipe chrome plated area with dry soft cloth, and sometimes wipe it

with cloth soaked in mild soap.

● If the dirt is difficult to clean, use neutral soap.
● In case of not using for a long time, sometimes spray to avoid rusty

ATTENTION

● Do not use abrasive cleaning material or tool such as detergents containing

hydrochloric acids, thinner, polishing powder, and nylon brush.

● Do not remove the cartridge, otherwise the shower will be damaged.

Unit: mm

OPERATING CONDITIONS

1. Water supply pressure: 0.05 ~ 0.75 MPa.

2. Ensure that supply water is clean (no sand, dirt, water soluble but

may precipitate substances such as Ca(HCO3)2,...).

3. Ambient temperature must be above 0oC.
4. The temperature of hot supply water from must not be exceed 85oC.

INSTALLATION GUIDE

BEFORE THE INSTALLATION

1. The hot water supply must be on the left, cold one on the right side.

2. The distance between hot water supply and cold water supply inlets

must be 150±20mm. Otherwise, you can not install the shower faucet.

3. In case the water supply pressure is greater than 0.75MPa, please use

the pressure relief valve (available in the market) to lower pressure
down to 0.2~0.3MPa. To have a refreshing feeling while using, set
water pressure of 0.2~0.3MPa.

4. In case the water supply pressure is too low (less than 0.05MPa), you must

increase the pressure by using pump or increase the water tank height.

5. For the hot water supply pipe from the water heater, to minimize the

loss, you should better lay the water supply pipe you should better lay
the water supply pipe with the shortest length. Wrap heat insulating
material or use heat insulating pipe.

6. Open valve to rinse sand, dirt, ect in the water suply inlets before installing.

HOW TO INSTALL

4. Install the hanger

Install installation holes then install hanger.

Expansion

Drill

2-Ø6 hole

Srew Hanger

5. Connect the shower

Connect the shower head to the hose
as the picture on the right side.
Connect the hose to the faucet.
Attention: Must install with packing.

6. Turn the cover to close to the wall

Packing

Nut

(4. Is the nut loose? Is the

packing scratched or
dirt)

Diverter

Packing

(5. Are the O-ring and

packing in the bottom

scratched or dirt?)

Diverter base

Spray head

(6. Is the packing scratched or dirt?

7. Is the filter clogged?)

Packing

(125)

2. Install the cover

Install the cover to con-
nector temporarily.

3. Install the shower faucet

Install the shower faucet to the
connector, you can adjust the
connector to install the faucet.

TROUBLESHOOTING

Trouble

Spray weak

Leak

Check point

7

2, 3, 4, 5, 6

Lever

Cartridge cover

Cartridge
(3. Are the O-ring
and packing in the

bottom scratched or
dirt?)

Cover

Trouble

Lever or esukatchon vibrates

Trouble of diverter

Screw
(1. Is it ightened?)

Red-blue eye

Nut

(2. Is it ightened?)

Diverter button

Check point

1, 2

5

Quantity

1pc

1 pc

Part name

Cover

Connector

Quantity

2 pcs

2 pcs

1. Install the connector

Use the seal tape, warp the thread of G1/2 of the connectors then
connect to the water supply inlets (hot and could).

Attention

● Inlets must indent from wall line 0~6mm, otherwise, you can not cover inlets.
● Adjust so that height of hot and cold connectors are equal, plane of

two connector ends is parallel with the wall line, distance between
connectors is 150mm.

Hot water

supply inlet

Cold water
supply inlet

Must be parallel
with wall line

HOW TO USE

● Pull the lever up to open, push the lever down to close.
● Turn left the lever to get hotter water, right to get colder water.
● Pull the diverter button up to get shower spray, push the diverter button down

to get faucet spray.

ATTENTION IN USING

● Use your hands to check water temperature before using to avoid burns.
● Do not touch the faucet’s left side or connector on the left to avoid burns.
● To avoid burn, set the water heater temperature not over than 60oC.

MAINTENANCE

45°

45°

25°

40°

15°

G1/2

Ø65

Max 1150

2.2 5

TOTO

BILL OF PARTICULAR

USER GUIDE

SPECIFICATIONS

TOTO

150

150±20

0~6mm

0IMI73201/04

Отзывы: