Total P20S Скачать руководство пользователя страница 9

 

Set up 

 

 

Functioning 

Always make sure the tool is turned off and the battery cartridge is removed before 

adjusting or checking the function on the tool. 

Installing or removing the battery cartridge 

 

 

1. Button 

 

2. Battery cartridge 

Attention 

  Always turn off the tool before installing or removing the battery cartridge. 

  Hold the tool and battery cartridge firmly when installing or removing the battery 

cartridge. Failure to hold the tool and battery cartridge firmly can cause them to 

slip out of your hands, resulting in damage to the tool and battery cartridge and 

personal injury. 

To remove the battery cartridge, slide it out of the tool while sliding the button on the 

front of the cartridge. 
To install the battery cartridge, align the tab on the battery cartridge with the slot in the 

casing and slide it into place. Insert it all the way until it clicks into place with a small 

click. If you can see the red indicator at the top of the button, it's not completely locked. 

Attention 

  Always install the battery cartridge completely until the red indicator cannot be 

seen. Otherwise, it may accidentally fall off the tool and injure you or someone 

around you. 

  Do not install the battery cartridge forcibly. If the cartridge does not slide in 

easily, it is not being inserted correctly. 

Attention 

  Before installing the battery cartridge into the tool, always check that the slide 

switch actuates properly and returns to the "OFF" position when the rear of the 

slide switch is pressed. 

  The switch can be locked in the "ON" position to facilitate operator comfort 

during extended use. Take care when locking the tool in the "ON" position and 

hold the tool firmly. 

Содержание P20S



















Отзывы: