background image

STEP • 14

STEP • 15

09

© Sheds (Midlands) Limited 2021

www.totalsheds.co.uk

= Drill Points using

screws provided as shown

SIDE & CORNER STRIPS

SIDE & CORNER STRIPS

Hide the panel edges.

Cover the framework & 

seams.

14a. 

Use all the side/corner strips to finish off the shed, by covering any exposed framework and 

the panel joining seams.

INFORMATION

 

The Corner Strips cover all panel edges. 

Remember to attach these to the exterior back 

panels too. 

14b

TACKS PROVIDED

ATTACH THE ROOF FELT

Use the felt lengths 

provided.

15a.

 Apply the roof felt as shown. Apply lower levels first to create 

correct rain run off positions.

15c. 

Trim down excess felt with a stanley knife. 

Remember to overlay the 1st felt to avoid rain leaks.

15d.

 Tuck and fold edges neatly and tack in place 

to hide any loose edges. Check that all areas are 

covered and there are no holes to avoid any rain 

water getting through your felt roof.

ROOF FELT

3rd

x2

4.0 x 70mm

 

Per Floor Section

x3

x3

4.0 x 70mm

Per Window Panel

14b. 

Each Strip requires 3 screws. Place these screws on the top, bottom and middle of the strip. 

15b. 

Using a hammer, tack down the felt with the tacks provided in a 

neat fashion.

Содержание Pent Potting Shed













Отзывы: