Toshiba Strata CIX IP5000 Series Скачать руководство пользователя

Страница: 174 / 216

Administrator Programming

IP5131-SDL Settings

156

Strata CIX IP5000-series Telephone UG 04/09

Headset Tx Volume Setting Screen



From the IP Configurations screen, select Sound >

> Headset Tx Vol. The Headset Tx Volume screen
displays.



To Change Information on this screen

1. Enter the New volume level.

2. Press the Set soft key to accept the change



...or press the Cancel soft key to cancel the change and
go to the Sound Setting screen 2.

Notes

•

Use the dial pad (1~0) to change or enter volume level. Press

Vol

to backspace.

•

You can enter a maximum of one digit.

•

Pressing the Set soft key can give you an Error Screen if you did not enter any data
or entered a non-numeric entry.

•

Press the Ok soft key on the Error Screen to correct the entry. Five seconds after
the Error Screen displays, the screen automatically goes back to the Headset Tx
Volume screen and the number that resulted in an error will be displayed.

Handset Rx Output Setting

1. From the IP Configurations screen, select Sound >

> Handset Rx Mode. The Handset Rx Mode screen
displays.

2. Press the On or Off soft keys to change the set value.

3. Press the Set soft key to accept the change.



...or press the Cancel soft key to cancel the change.



The changed setting is underlined in the Sound screen
display.

Headset Tx Volume

Backspace = Vol-Down

[Set]

[Cancel]

Config

:Current

:New (0:Min. - 7: Max)

Handset Rx Mode

Off

[Set]

[Cancel]

Config

Содержание Strata CIX IP5000 Series

























































































































































































































Результаты поиска

Содержание Strata CIX IP5000 Series

Отзывы:

Похожие инструкции для Strata CIX IP5000 Series

Бренды по названию

Популярные бренды

Toshiba Strata CIX IP5000 Series, Руководство пользователя

Результаты поиска

Содержание Strata CIX IP5000 Series

Отзывы:

Похожие инструкции для Strata CIX IP5000 Series

Бренды по названию

Популярные бренды