38
Programming a recording (REC MENU) (Continued)
Recording
Correcting a timer program
1) Press MENU.
2) Press / to select “Timer recording”, then
press OK/ENTER.
3) Press / to select a timer program you want
to change, then press OK/ENTER.
4) Follow steps 4 to 6 (
page 36, 37) to change
the settings.
5) Press EXIT to exit.
Important
• You cannot correct a timer program within 5 minutes before
the recording start time. You can only delete the timer
program.
Deleting a timer program
The maximum timer program capacity is 32. Any new
program will be rejected if the recorder is full. To enter a
new program, you must cancel an existing one.
1) Press MENU.
2) Press / to select “Timer recording”, then
press OK/ENTER.
3) Press / to select a timer program you want
to delete.
4) Press QUICK.
The Quick Menu appears.
5) Press / to select “Program cancel”, then
press OK/ENTER.
Check the message, then delete the entry.
Note
• You cannot delete a timer program while another is being
executed.
To stop a programmed recording
1) Select the recording drive by pressing HDD or
DVD twice.
2) Press STOP on the front panel twice.
When you press the STOP button once, a message
appears. While the message is displayed, press the
STOP button once again.
Note
• If you press the STOP button on the remote control, a
message appears. Select “Yes”, then press the OK/ENTER
button.
Checking the remaining volume
1) On REC MENU Timer Programming, press
QUICK.
2) Press / to select “Disc budget calculation”
then press OK/ENTER.
The Disc budget calculation menu appears.
3) Press / to select a timer program, then
press OK/ENTER.
The recorder calculates on a bar graph how much
a specific program (identified by a check mark) will
occupy on the disc.
Pressing the ADJUST button can display or remove
the check mark.
4) Correct the parameters of the timer program if
necessary.
(Skip to step 6) if you do not need this.)
Select an item you want to modify and press the
OK/ENTER button. The item will be ready to be
altered.
(When “High rate save” is set to “On”, “Pict.” cannot
be changed.)
Press the ADJUST button to modify. When
complete, press the OK/ENTER button.
5) Press MODE.
Program modification is registered.
6) Press EXIT to exit.
Notes
• The nearest 8 programs are calculated at a time.
• While the recorder is preparing for or executing a
programmed recording, any program modification cannot
be registered. Only programs which will start after 5
minutes or later can be modified.
• Available disc volume is not displayed for a DVD-R/RW
disc on which DVD-Video finalize process was executed.
e.g.
4/23(Su)17:50
Disc budget calculation
REC
MENU
Ch
Date
Start
End
Pict. Audio
Page
1 / 1
1
10
42
4
-
4/30(Su)
5/17(We)
5/20(Sa)
5/27(Sa)
7:00
8:30
-
9:30
10:00
-
10:30
11:30
-
8:30
11:30
MN 6.6
HDD
HDD
HDD
D/M2
MN 6.6
D/M2
LP 2.2
D/M1
SP 4.6
D/M2
DVD
DVD
DVD
Media
Result
Elapsed
Available
Selected(current)
(
)
Selected programme Available disc space
When the entry item is marked X, the recording will
not fit. Change the setting.
means this recording will not be executed due to
overlapping programme.
RD-85DT_Ope_E_p031-044
3/30/06, 14:34
38
Содержание RD-85DTSB
Страница 52: ...RD 85DT_Ope_E_p050 056 3 27 06 19 41 52 ...
