Toshiba RAV-GM1101AT8JP-E Скачать руководство пользователя страница 59

Страница: 59 / 84

Check

code

Outdoor

LED display

Check and troubleshooting

(Item without special mention Indicates part of outdoor unit.)

FILE NO.SVM-18044

-2

59 -

[4-way valve inverse error]

[P19]

Is operation of 4-way valve

correct?

(Check pipe temp. and etc. in

cooling/heating operation.)

Are temperature sensors

correct?

TE sensor: GM110, 140 :

CN601 TS sensor: GM110,

140 : CN600

YES

Are resistance value

of indoor TC and TCJ

sensors correct?

Check and

replace of PMV

Replace TE sensor.

Replace TS sensor.

Replace coil

of 4-way valve.

Replace TC sensor

Replace TCJ sensor

Is the 4-way valve

coil is normal?

(Check the resistance value

of 4-way valve coil)

Does power supply to 4-

way valve coil when

4-way valve is operated?

Check outdoor

P.C. board.

Check indoor P.C. board.

Defect

→

Replace

Check 4-way valve.

Defect

→

Replace

Check outdoor

P.C. board.

Defect

→

Replace

YES

Error

YES

Is refrigerant flow by

PMV correct?

YES

[P20]

[High pressure protective operation]

Reset the power supply

and then make a test run.

Open service valve fully.

Check outdoor fan.

Defect

→

Replace,retightening

Is service valve

fully opened?

Is there any defect such as

loosening of nut in the outdoor fan?

Does the outdoor fan perform

abnormal operation?

Is resistance value

TE sensor correct?

Replace TE sensor.

Check the same items as

[P22] error.

Check overcharge of refrigerant, clogging of

cycle, broken pipe, abnormal overload, etc.

Defect

→

Correct defect.

Eliminate interfering element.

Is there anything

which interfere heat exchange

of outdoor unit?

• Clogging of heat exchanger

• Short-circuit

YES

Содержание RAV-GM1101AT8JP-E





















































































Результаты поиска

Содержание RAV-GM1101AT8JP-E

Отзывы:

Похожие инструкции для RAV-GM1101AT8JP-E

Бренды по названию

Популярные бренды

Toshiba RAV-GM1101AT8JP-E, Руководство по обслуживанию

Результаты поиска

Содержание RAV-GM1101AT8JP-E

Отзывы:

Похожие инструкции для RAV-GM1101AT8JP-E

Бренды по названию

Популярные бренды